0
What else can I help you with?
What is definition of isolated footing and how it design?
Isolated footing Transfers individual column loads directly to the soil. If a single spread footing interferes with another spread footing, the two can be combined to form a combined footing.
What does strip footing does?
Suppose a number of columns in a row are to be supported on a soil of such low bearing strength, that separate bases if provided would overlap,a practical solution would be to provide a column footing to support all the columns of the row. such a footing is called a "STRIP FOOTING"
What is a stab column?
Stab column is the one which does not have footing and pedestal support(reinforcement), which it rises from beams or slabs for upper levels.- K @ $ !civil engineering - GITAM UNIVERSITY
What size footing you need for a 6x6 column on a roof?
The size of the footing required for a 6x6 column supporting a roof typically depends on factors like the load the column will bear, soil type, and local building codes. A common guideline is to use a footing that is at least 24 inches by 24 inches and 12 inches deep, but this may vary. It's essential to consult with a structural engineer or local building authority to ensure compliance with specific requirements and safety standards.
What is a stub column?
its nothing its a simple reduntant compression/ tension member which even can be horizontal depending on the type of load....sometimes it has footing and sometimes it doesn't depending on the length of the column.
What is definition of isolated footing and how it design?
Isolated footing Transfers individual column loads directly to the soil. If a single spread footing interferes with another spread footing, the two can be combined to form a combined footing.
What is footing?
pad footing is the base of a column that transfers the load to the foundation.
What is column footing details?
I believe it is the details of the base of a column.
What is pad footing?
pad footing is the base of a column that transfers the load to the foundation.
What does strip footing does?
Suppose a number of columns in a row are to be supported on a soil of such low bearing strength, that separate bases if provided would overlap,a practical solution would be to provide a column footing to support all the columns of the row. such a footing is called a "STRIP FOOTING"
What is the purpose of gavel base to the column footing?
drainage
What is a pedestal in a footing?
A pedestal in a footing is a portion of the footing that is designed to support a concentrated load, such as a column or pier. It typically has a smaller cross-sectional area than the main footing and is used to distribute the load from the structural element to the larger footing below. The pedestal helps to prevent excessive settlement or bearing capacity failure at the column support point.
What is an individual backbone called?
An individual backbone is called a "vertebral column" or "spine." It is composed of a series of individual bones known as vertebrae, which are stacked on top of each other to form the column. The vertebral column protects the spinal cord and provides structural support for the body, allowing for flexibility and movement.
What is the place where a column and row meet called?
The place where a column and a row meet is called a cell. Each individual cell is addressed by the (row, col) notation.
What is the minimum anchorage length for reinforcement?
It is the length of the main bar provided at the column beam junction or column footing junction to allow for the development of stresses to its design strength.
What is a stab column?
Stab column is the one which does not have footing and pedestal support(reinforcement), which it rises from beams or slabs for upper levels.- K @ $ !civil engineering - GITAM UNIVERSITY
What size footing you need for a 6x6 column on a roof?
The size of the footing required for a 6x6 column supporting a roof typically depends on factors like the load the column will bear, soil type, and local building codes. A common guideline is to use a footing that is at least 24 inches by 24 inches and 12 inches deep, but this may vary. It's essential to consult with a structural engineer or local building authority to ensure compliance with specific requirements and safety standards.
