This can be done with an Equalizer. ANSWER: Not an equalizer for sure not unless the distortion is frequency related.
normal amplifier is a mathametical operation analog the computer, magnetic amplifier is sound operation of the signal
pinagdugtong na madaming amplifier
Usually output of an amplifier is a voltage ,...but in case of Operational Transconductance Amplifier ,Iout (current ) is the output. This feature, makes it useful for Electronic control of amplifier gain .
The amp for audio freq. is a AF amplifier. The RF amp is for radio freqs.
The Bose 901 speaker system includes an equalizer that is generally connected between the pre-amp and the power amp. In many cases, this will be a "tape out" connection and a "tape in" connection. To add an additional equalizer, connect the output of the Bose equalizer to the input of the additional equalizer. Then, the output of the new equalizer is connected to the amplifier input that the Bose equalizer was originally using.
Connect the sub woofer to the equalizer or amplifier. The positive wire will need to be connected to a power source. Connect the ground wire. Connect the auxiliary wire to the amplifier.
Yes, it goes in series in the audio path. The output of the CD player connects to the input of the Equalizer and the output connects to the input of the Receiver or Power amp.
The point of a car amplifier is the make music sound better, so in most cases all amplifier make music sound better.
Well let's say you want to use your 'CD player' on your equalizer. (just for example) So we take the rca cord coming from your CD player and hook it to your equalizers INPUT. Then run the equalizers output to the INPUT on your amplifier/receiver. Make sure everything is on and equalizer is not defeated and you can start adjusting!
If the sound system in your car just doesn’t seem to blast your music loud enough for you, it might be time to think about installing a car equalizer. A car equalizer can essentially control all of the frequency bands that come along with different radio stations, CDs, and MP3s. Without a car equalizer, you would constantly be needing to change the various levels on your player. Now that you know what an equalizer is, how exactly do you get said equalizer installed into your vehicle? The first thing that is an absolute MUST is to turn off all power sources to your car. You are going to be working mostly with the wiring and the fuse boxes when you are installing your car’s equalizer, so you most assuredly don’t want to be surprised when your car has a power surge and you are working in the fuse box. Now you are going to want to decide where you want the equalizer to be in your car. Most people are going to put them on the dashboard because it gives them an easy place to adjust the equalizer as needed. If your equalizer did not come with some form of mounting piece, you may have to use a makeshift holder to get it to stay on your dashboard. Once you have the car equalizer mounted, you will need to take some 16-gauge wire and plug it in to the panel of fuses where it says power in. You’re then going to be able to hook the main unit of your stereo system to the equalizer by running a wire from the stereo to the equalizer. You will need to remove the covering at the end of the wire that turns your unit on as well as removing the covering from the end of the wire you plugged into the equalizer. Tape these two pieces of wire together with black electrical tape. Next, you are going to need to relay the wire for turning the system on. The RCA cables originating from the main unit are going to need to be connected to the outlets of the amplifier. Take these cables so that you are putting the equalizer and the amplifier cables together. From the outlets of the amplifier, you will need to run the RCA cables to the inlets of the equalizer. After you’ve completed all of these steps, just put the main unit back into the dash, turn your equalizer on, and enjoy a most stable music experience.
I have one of these graphic equalizers and if your amp has a dedicated output and input for a graphic via a phono connector then it will work. If it doesn't then you could add a phono connector switch. This device would have inputs for all your devices via phono connectors (cd player, computer, satellite receiver etc) and it would have one output which would go into the graphic equalizer then out of it into one input on your amplifier. You would then select the individual device on the phono connector switch which you are going to play and select the solitary input on your amplifier.
Series is better, it can handle more flow to it.
Sony has the best car amplifier on the market. These are typically more expensive as well.
The Equalizer ended on 1989-08-24.
You need to match the speaker with the amplifier. Better or worse is not the question. The question is dynamic range and the possibility of overloading the amplifier. If the amplifier is rated 4 ohms, use a 4 ohm speaker. Same for 8 ohms. Do not "mix and match".
Alpine by far.