0
In HVDC (High Voltage Direct Current) transmission systems, the primary types of cables used are underground cables and submarine cables. These cables are typically made from materials like cross-linked polyethylene (XLPE) or oil-filled cables, designed to withstand high voltage and environmental conditions. They are insulated to prevent electrical leakage and ensure safe transmission over long distances. Additionally, the use of bipolar cables allows for efficient transmission and improved reliability in the system.
What else can I help you with?
What kind of bridge is the Zakim Bunker bridge?
i believe it is a cable stayed bridge
What is a kind of bridge hung from cables?
The type of bridge hung from cable is called Suspension CableA cable suspension bridge is a kind of bridge hung from cables.
What kind of animal uses hydraulic system to move?
Echinoderms
What kind of transformer is used to change the voltage of electric current in transmission lines before it enters houses in a neighborhood?
It's called a 'distribution transformer', as opposed to a 'power transformer' which is used in the transmission and primary-distribution electrical systems.
Why is serial transmission preferred for long distances?
Because the costs are small than other kind of transmissions. For example, in case of 8 bits data transmission, parallel aprouch needs 8 wires but serial only 1 (cheapest).
Where is the odometer cable located?
Not sure what kind/year of car you have. The odometer and speedometer are both driven by the same cable. The cable goes forward from the back of the speedometer, throught the fire wall and down to the transmission. You should be able to see where the cable protrudes through the firewall. Some cars use an electrical transducer instead of a cable. The transducer is mounted in the transaxel, has an electrical cable and connector going to it, probably two wires. The speedometer on this system is electronic and receives an electrical signal from the transducer. There is nothing different looking about the speedometer to immediatly indicate which system you have. Good Luck
What kind of electric cable is capable of 240 volts transmission?
When cable reference is made about voltage it is the cables insulation factor that comes into play. Cables in North America have common voltage ratings of 300, 600 and 1000 volts. A cable capable of handling 240 volts will have a rating of 300 volts. The ratings of each specific cable is printed on the cable's outer jacket.
What kind of different TV cables are there?
There are five different types of TV cables one could use for their system. These are component video cables, composite cable, coxial RF cable, s-video cable, DCI and HDMI cables.
What kind of power steering fluid is used for a 2005 Sprinter?
The power steering system uses automatic transmission fluid.
Why cant you find your gear shift cable on the transmission of your 2001 kia sportage?
i think on the 2001 model the linkage connects directly to the tranny. kind of like the old 64 chevys.
What kind of cable to hook the 2nd computer into the router?
Ethernet cable
What kind of television signal is Time Warner cable?
A cable signal.
How do i connect a PS3 to a Phillips DVD surround system?
hook up your ps3 to your television (with HDMI cable) and depending on what kind of television you have, you need to send the audio out to the sound system. I used an optical cable for the best quality sound. Now, no matter what is hooked up to your television, it will go through your sound system.
What Kind Of A Transmission Does A Lamborghini Have?
A 350 GTV Transmission
What kind of transmission does your 94 camaro have?
automatic transmission
What kind of transmission fluid does a 91 capri use in the transmission I know it is a standard however when the actual transmission is damaged and the seal is broken you need to put oil in it?
It should say on the hood of the car. I used dextron III fluid in my manual transmission and it has been working fine. The only way to fill it is through where the speedometer cable fits into the transmission near the rear of the motor. After taking out the speedo cable, you need to unbolt the 10 mm bolt next to the speedo cable mount and pop off that attached piece that the 10 mm bolt was holding on. I had to get underneath the car and pop it off with a screwdriver and hammer after the 10 mm was out. Might be difficult.
Does 10BaseT cable need terminators?
Every transmission line requires termination, either in the form of the ultimate load, such as an antenna, or in the form of some kind of resistor. 10BaseT is no different.However, that termination is usually built in to the device in which the cable is plugged. This is different from older systems, such as ArcNet, where the coax cable requires termination on each of the far ends. This is because the 10BaseT system is a star system rather than a partial ring system, so the termination is not a function of the chosen topology.The reason termination is required in a transmission line is that every step change in characteristic impedance encountered by the wave front as it propagates through the line results in some kind of reflection back towards the source. These reflections result in distortion, loss of power, even damage to the transmitter or circuit.To reinforce this understanding, consider the 75 Ohm coax cable typically used in a television distribution system. In the simplest case, you connect a cable from the service entrance to the TV set, and you are properly terminated. If, however, you use a splitter, such as for a TV set and a VCR, you now have three transmission lines, one to the splitter and two from the splitter. Is the RF output of the VCR connected to something? It should be, either to a TV set or to a terminator, otherwise there will be problems due to ringing, interference, ghosting, etc.
