0
What else can I help you with?
How do you calculate voltage drop for starting motor current and how to get the starting pf?
How do you calculate voltage drop for starting motor current
If the resistance increases what will happen to voltage and current?
If you have a simple circuit. For eg: One voltage source and one resistor, then the voltage of the circuit will always remain the same, the current however will decrease following Ohms' Law V=I*R. If we have a current source instead of a voltage source, we are forcing the current to be a certain value so if we increase the resistor value the current will remain the same but the voltage will increase.
Technician A says that the current draw should decrease as the voltage decreasestechnician B says that the current should increase as the voltage decreases Which technician is right?
Both technicians are right, and both technicians are wrong, because not enough information is present in the question, nor in their statements. Given constant impedance, current should decrease as voltage decreases, while given constant power, current should increase as voltage decreases.
Which statements about series circuits are correct?
series circuits have 1 pathway they have constant current(Amperes) not constant voltage. Resistance=R+R+R+...
Can there be a current with no voltage?
No, There can't Be current without voltage
How do you calculate voltage drop for starting motor current and how to get the starting pf?
How do you calculate voltage drop for starting motor current
Why is rise in voltage less during stopping of load than drop in voltage during starting?
The voltage drop during starting a load specially motor load is due to absence of back emf and due to high starting current drawn. In case of resistor/heaters, they are also wound like coil so they will also have some inductance and hence during starting, due to absence of back emf, a high current is drawn and hence the voltage drop. While stopping the load current drawn is smaller than the starting current. In the cases of motors and transformers their starting current is about 6 - 8 times the full load current and hence the above phenomenon asked in the question is observed.
If the resistance increases what will happen to voltage and current?
If you have a simple circuit. For eg: One voltage source and one resistor, then the voltage of the circuit will always remain the same, the current however will decrease following Ohms' Law V=I*R. If we have a current source instead of a voltage source, we are forcing the current to be a certain value so if we increase the resistor value the current will remain the same but the voltage will increase.
What are some examples of statements that apply to resistors?
For example, you can write statements based on:* Ohm's Law: V = IR (voltage = current x resistance) * Power dissipation: P = I squared R
Technician A says that the current draw should decrease as the voltage decreasestechnician B says that the current should increase as the voltage decreases Which technician is right?
Both technicians are right, and both technicians are wrong, because not enough information is present in the question, nor in their statements. Given constant impedance, current should decrease as voltage decreases, while given constant power, current should increase as voltage decreases.
What would be the starting current of any Air Conditioning if voltage is 220?
To calculate the starting current of a motor, the run current must be stated. The voltage is only associated with this calculation in as the higher the motor's voltage is the lower the run current is. The start current can be as high as 300 to 600 percent of the run current. Also taken into account, without the specific make and model of the A/C, the run current is hard to guess as there is quite a variety of amperage drawn by these units.
How the current in a circuit changes if the voltage in the circuit is decreased and the resistance remains the same?
If the ratio of voltage to current is constant, then the circuit is obeying Ohm's Law. If the ratio changes for variations in voltage, then the circuit does not obey Ohm's Law.
What is the relationship among voltage current and resistance in a circuit?
Voltage = (current) x (resistance) Current = (voltage)/(resistance) Resistance = (voltage)/(current)
What is a relationship among voltage current and resistance in a circuit?
Voltage = (current) x (resistance) Current = (voltage)/(resistance) Resistance = (voltage)/(current)
What is the connection of normal wire star or delta?
normally delta connection wired in 3 phase induction motor. during starting wiring is in Star and after running normal speed changeover to delta .beacause starting time its phase voltage equals less root3 times of line voltage ,line current and phase current equals. in Delta phase voltage and line voltage equals, and phase current equals root3 times line current
What is starting current for a 6.7kw 3 phase electric motor?
One need to know the voltage, the power factor and starting torque, to derive the starting current. The information provided in the question is not sufficient.
Which statements about series circuits are correct?
series circuits have 1 pathway they have constant current(Amperes) not constant voltage. Resistance=R+R+R+...
