answersLogoWhite

0

Micrometer is having a ratchet to rotate which is pre-loaded to get standard thrust while measurement, whereas in the case of a vernier the accuracy of measurement depend on the pressure each individual applying while the measurement.

User Avatar

Wiki User

8y ago

What else can I help you with?

Continue Learning about Engineering

What type of micrometer is easiest to read?

A digital micrometer is the easiest to read as it displays the exact reading on a screen.


HOW TO USE A screw-thread micrometer?

First calibrate the micrometer by dialing the spindle to zero and adjusting the anvil until it is flush against the spindle. Measure the screw until the ratchet begins to click and take the first reading. This reading can then be compared to a machining book to verify the pitch diameter.


How does one avoid lifting of the bridge of the depth micrometer?

To avoid lifting of the bridge of the depth micrometer, make sure that the spindle is correctly positioned before taking a reading. The spindle should be parallel to the base of the depth micrometer and should be positioned directly over the object being measured. Make sure that the object being measured is firmly supported and that the work surface is free of debris that may interfere with the depth micrometer’s operation. Before taking a reading, check that the anvil and spindle are perfectly aligned with each other. Avoid pressing down on the depth micrometer too hard as this can cause the bridge to lift. Always use the correct size micrometer for the job and the correct size anvil for the object being measured. If the bridge does start to lift, stop and correct the problem before taking any further readings. Before taking a reading, always make sure that the depth micrometer is properly zeroed. When using a depth micrometer, always keep your hand away from the spindle and anvil. Make sure that the depth micrometer is properly maintained and stored in a dry, clean environment. Lastly, always use the depth micrometer with care and caution to avoid any damage or inaccuracy.


On a good compressor using an ohm meter you should get a positive reading from common?

Well, isn't that a happy little question! When testing a compressor with an ohm meter, you should get a positive reading from the common terminal. This indicates that the winding inside the compressor is intact and functioning properly. Just remember to always refer to the manufacturer's guidelines for specific readings and instructions.


How do you Verifypositive and negative wires with a multimeter?

To verify positive and negative wires with a multimeter, set the multimeter to the DC voltage setting. Connect the black probe to the negative terminal (common), and the red probe to the wire you want to test. If the multimeter displays a positive voltage, the wire is positive; if it shows a negative voltage, the wire is negative. If the reading is zero or close to it, the wire may not be energized.

Related Questions

What is the 'zero error' in vernier calipers and micrometer screw gauge?

In vernier calipers, zero error is when the jaws of the caliper do not close properly when they are in contact without measuring anything, resulting in a measurement that is not accurate. In a micrometer screw gauge, zero error occurs when the flat end of the spindle does not perfectly align with the reference line on the sleeve at zero reading, leading to inaccurate measurements.


What type of micrometer is easiest to read?

A digital micrometer is the easiest to read as it displays the exact reading on a screen.


What is positive zero error in a micrometer?

This is the measurement recorded when, in fact, it should be 0. It is the measurement when there is nothing to measure but the reading is not exactly 0 because the calibration has gone off.


When reading a small-hole gauge how is the micrometer reading taken in relation to the split in the ball on the split or 90 degrees to it?

When reading a small-hole gauge, the micrometer reading is taken at the point where the split in the ball aligns horizontally at 90 degrees. This allows for an accurate measurement of the diameter of the hole based on where the micrometer lines up with the scale on the gauge.


To what decimal can you estimate the reading on a micrometer?

My micrometer reads out to ten-thousandths of an inch.EX: .2501".This is 250 thousandths plus 1-ten thousandths of an inch.I never guesstimate a reading...Hope this helps


How tight is the thimble turned when testing zero on a micrometer?

All you need to do is make contact. Tightening will give you a false reading and eventually damage the micrometer.


What is the instrument used to measure diameter of testtube?

Calipers measure the internal or external dimensions of something.


What is the expected Error using micrometer?

the spindle must be tighten to avoid slightly changes on the reading


HOW TO USE A micrometer?

First calibrate the micrometer by dialing the spindle to zero and adjusting the anvil until it is flush against the spindle. Measure the screw until the ratchet begins to click and take the first reading. This reading can then be compared to a machining book to verify the pitch diameter.


What are the many positive for reading that are available to modern man?

positive avenues for reading


What is maximum reading of micrometer screw gauge?

The maximum reading of a micrometer screw gauge depends on the number of divisions on the thimble and the barrel. Typically, it can measure up to 25 millimeters with a resolution of 0.01 mm on the main scale and an additional fraction of a millimeter based on the thimble divisions.


How do you read micrometers?

Difficult to explain without diagrams, but the micrometer relies on an accurate screw which advances the caliper a precise amount with each revolution. So you turn the screw until the object is lightly held, then read the axial scale and add on for the number of screw turns above the nearest scale reading. The most accurate type also have a vernier scale for very small distances. I suggest you look at Wikipedia 'Micrometer' which has a thorough explanation with diagrams.