answersLogoWhite

0

What else can I help you with?

Continue Learning about Engineering

Is it essential to use a baby stair gate?

No it is not essential to use a baby stair gate. If the baby is located at a home without stairs, there would be absolutely no need for one. On the other hand, if the location has any stairs, or even rooms that a parent does not want the baby near, a gate is imperative.


What is the stream of particles originating from a cathode in a vacuum tube?

Not sure of the question, but *electrons flow from cathode to plate in a CRT. A deflection coil guides the electron beam to various areas of the screen. Some CRTs use electrostatic deflection, where the beam is deflected by four grids that steer the beam.


How do you install Spring Loaded Gate Casters?

To install spring-loaded gate casters, first, position the caster brackets on the gate at the desired height, typically near the bottom corners. Mark the drilling holes and then drill pilot holes for the screws. Attach the brackets securely using screws, ensuring that the spring-loaded mechanism faces outward for proper functionality. Finally, test the gate's movement to confirm that the casters operate smoothly and provide the necessary support.


Gate input is LOW-ACTIVE?

A LOW-ACTIVE gate input means that the gate's output is activated or enabled when the input signal is at a low voltage level (typically near 0 volts). In digital logic circuits, this characteristic is often seen in components like NAND and NOR gates. For example, a LOW-ACTIVE NAND gate will produce a high output unless all its inputs are low, while a LOW-ACTIVE NOR gate will produce a high output only when all its inputs are low. This behavior is essential for designing logic circuits that respond to specific input conditions.


Why terminal voltage of the self-excited shunt generator lower than that of the separately excited shunt generato?

Some generators are self excited; this means their terminal voltage is fed back to the excitation system to supply power to the rotor of the generator (which makes it into an electromagnet); the more power that is fed back, the stronger the electromagnet becomes, which makes it harder to turn the generator, which causes the generator to push out more power (simplified, really quick version). If there is a fault electrically near the terminal of a self excited generator, the terminal voltage will sage to near zero; this means the voltage supplied to the excitation system will drop by the same percentage (say the terminal voltage is 30% of what it should be, then the maximum supplied voltage to the excitation system drops to 30% of what it normally is, since P = V*I). Since the input power is less, the output of the generator will decrease (current will decrease). The terminal voltage is determined by the impedance between the generator and the fault such that V = I*Z; As I decreases, V will also continue to fall, causing the terminal voltage to sag even more. A non-self excited generator gets its' excitation power from the grid, specifically from a location that is electrically separated from its' terminal voltage. If the terminal voltage sagged to 30% (same fault location as above example), the excitation system voltage may be impacted slightly (say 2%) so the excitation system power is near maximum (98% for this example). Since the excitation system is much farther removed from the terminal voltage, it is not dependent upon it, thus the terminal voltage will not continue to sag as with a self excited system.

Related Questions

How can you distinguish between positive and negative terminals?

Positive terminals typically have a red color or a "+" sign indicated, while negative terminals are usually black or have a "-" sign marked. Additionally, positive terminals are connected to the cathode, while negative terminals are connected to the anode in a battery or electrical device.


Is there a designated smoking area at Frankfurt airport?

YES, I passed by FRA in JULY 2008 and smoking cubicles have been commissioned and are located near the duty free area in Terminal B. Terminal 1 departures B, level 3, near SEB-Bank Schengen A, between Gate A 23 und A 25 Schengen A, between Gate A 30-32 Schengen B, near Gate B 3-9 Transit A, between Gate A 63 und A 65 Transit B, near Gate B19/ B20 Transit B, near Gate B 41 Transit C In public area. smoking is only permitted outside the building.


What does the airport term left the gate mean?

"Left the gate" means an airplane has vacated the airport's departure gate, normally to begin the taxi to the departing runway. This could also refer to a person who left the area near the departure gate inside the terminal.


Why does in a potato when connected to a circuit appears blue near the positive terminal?

copper salts are forming on that electrode and diffusing into the potato flesh.


What is a Programmable unijunction transistor?

PUT: programmable unijunction transistor It is a device like the thyristor only the gate is connected to the N type material near the anode. It is usually used in time delay, logic and SCR trigger circuits In the PUT, Gate is always positively biased w.r.t cathode. When anode voltage exceeds the gate voltage by about 0.7 V, first junction that is the junction right after the anode gets forward biased and PUT turns on. When anode voltage becomes less than the gate voltage, PUT is turned off.


Was the cathode ray slower than the speed of light?

No, the cathode ray is faster than the speed of light.


Wiring starter relay on a 1990 ford bronco?

To wire the starter relay on a 1990 Ford Bronco, first locate the relay, typically found near the battery or on the fender. Connect the battery positive terminal to the relay's input terminal, then connect the output terminal to the starter motor. The ignition switch wire should be connected to the relay's control terminal, and the relay's ground terminal should be connected to the chassis. Ensure all connections are secure and insulated to prevent shorts.


Where are negative and positive terminals under hood of S430?

In the Mercedes-Benz S430, the positive terminal is typically located near the front of the engine bay, often near the battery or connected to a designated jump-start point. The negative terminal is usually connected to the car's chassis or engine block, providing a grounding point. Always refer to the owner's manual for precise locations and guidelines when working with the vehicle's electrical system.


What would cause weak spark on a 1986 d100 dodge?

I have the same problem with a '82 Poweram 150 - It was suggested to me that it could be the engine is improperly connected to the negative terminal on the battery. Take jumper cables and ground one side to the negative terminal, the other clipped to the engine near the distributor. Might do the trick. I have the same problem with a '82 Poweram 150 - It was suggested to me that it could be the engine is improperly connected to the negative terminal on the battery. Take jumper cables and ground one side to the negative terminal, the other clipped to the engine near the distributor. Might do the trick. WEAK COIL...


Where is the nearest available seat at Gate Delta"?

The nearest available seat at Gate Delta is located near the gate area.


Where is the jump start post in a 2004 Mercedes s500?

In a 2004 Mercedes S500, the jump start post is located in the engine compartment. It can be found on the driver's side, near the front of the vehicle, typically near the battery. Look for a plastic cover that indicates the positive terminal, which is marked with a "+" sign. The negative terminal is usually connected to a ground point nearby.


Is there any restaurants near the Golden Gate bridge?

no