Nice Question:
It is done for 2 basic reasons:
1. If a flat or a concrete surface is used then there are chances of water accumulation during rain which must be avoided in Yards.
2. Lets suppose if there is any oil spill or leakage in transformer, then the oil can never got accumulated on surfaces. Instead, it will seep from gravel into bottom thereby minimizing chances of fires.
One yard of PEA Gravel weighs approximately 3,000 pounds Clarification: one CUBIC yard weighs approx 3,000 pounds.
i saw $20-25 for coin size type gravel
To mix 1 yard of concrete, you typically need about 1.5 tons of sand and 1.5 tons of gravel. This is based on a common concrete mix ratio of 1 part cement, 2 parts sand, and 3 parts gravel. Therefore, for 1 yard of concrete, you would use approximately 0.5 yards of cement, 0.75 yards of sand, and 1 yard of gravel. Always consider adjusting the proportions based on specific project requirements or desired concrete strength.
On average it would be 1,5 ton a yard but depending the type of stone it might be up to 1,8 ton
A transformer used to step up or down the value of voltage.
A yard of gravel is the amount of gravel that will fill a container whose inside dimension is 1 yard by 1 yard by 1 yard. It's a cubic yard of gravel. The metric equivalent is .9144 meters by .9144 meters by .9144 meters.
A "yard of gravel" is a measure of volume, not a measure of area. There are 27 cubic feet (3x3x3 feet) in a yard of gravel, or one cubic yard.
One yard of gravel typically weighs between 1.5 to 2 tons, depending on the type and composition of the gravel. On average, you can estimate about 1.5 tons per yard. Therefore, for specific projects, it's important to check the density of the gravel being used for a more accurate conversion.
The weight of gravel can vary depending on its type and moisture content, but on average, 1 cubic yard of gravel weighs approximately 2,500 to 3,000 pounds. This means that 1 yard of gravel typically weighs around 2,700 pounds. For more precise measurements, it’s best to check the specific type of gravel being used.
This depends on the size of gravel, the water content of the gravel, and the material composition of the rock used to make the gravel. Typically 1 cu.yd. of gravel wieghs 3000 lb.
No, a cubic yard of gravel will have a different volume measurement compared to a cubic yard of dirt because they have different densities. Gravel is denser and heavier, so it will take up less volume than dirt in a cubic yard.
A yard of dry sand typically weighs more than a yard of dry gravel. Sand particles are smaller and more densely packed, while gravel consists of larger particles with more empty space between them, leading to gravel being less dense overall.
The amount of water a cubic yard of gravel can absorb varies depending on the type of gravel and its porosity. On average, gravel can absorb around 20-30% of its volume in water. This means that a cubic yard of gravel can potentially absorb around 200-300 gallons of water.
A cubic yard of gravel will cover 81 square feet at 4" of thickness. Multiply the width of the patio by the length of the patio to get your square footage. Gravel is usually sold by the cubic yard.
The weight of gravel can vary depending on its type and moisture content, but a common estimate is that one cubic yard of gravel weighs about 1.5 tons. Therefore, 3,000 yards of gravel would weigh approximately 4,500 tons (3,000 yards × 1.5 tons per yard). Always check the specific weight for the type of gravel being used for a more accurate calculation.
One yard of PEA Gravel weighs approximately 3,000 pounds Clarification: one CUBIC yard weighs approx 3,000 pounds.
One cubic meter of gravel weighs approximately 1500 kg