answersLogoWhite

0

The low slip test is used to determine the D and Q axis impedance of salient pole machines. The machine terminals are short circuited, each phase voltage and current are measured. Since the terminals are short circuited, machine voltage must be reduced to prevent excessive output currents that would damage the machine.

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Engineering

How do you test the 11KV HT cables?

The test equipment used to test high voltage cables is a hi-pot test where a high DC voltage is a applied to the cable. This voltage can be from 150% to 200% of the working voltage of the cable.See related links below.


What is withstand voltage?

It is the rated test voltage that will not cause insulation breakdown.


What is voltage test?

dirct current


How can design stick-slip machine?

Stick-slip machines are designed to provide more controllable motion than a traditional electric motor. The basic design consists of a motor a control board and a stick-slip mechanism. The motor is used to provide the power to move the stick-slip mechanism while the control board is used to regulate the speed and position of the mechanism. The stick-slip mechanism consists of an elastic element such as a spring or rubber band that is connected to a shaft. When the shaft rotates the elastic element is compressed and then released creating a stick-slip effect. To design a stick-slip machine the following steps must be taken: Choose an appropriate motor and control board. Design the stick-slip mechanism and select an appropriate elastic element. Select the appropriate shaft and bearing system. Integrate the motor control board stick-slip mechanism and shaft into a single system. Test the system and adjust as necessary for optimal performance.By following these steps it is possible to design and build a reliable controllable stick-slip machine.


What is the difference between the working voltage and test proof voltage for dielectric footwear?

Working Voltage is the voltage at which the boot is safe at. Test Proof voltage is what the boot was tested up to before it failed. However you must keep in mind that if you are in wet conditions that can significantly lower the rating of the boot. Also voltage does not kill you it is the amperage.

Related Questions

No load current of transformer is non sinusoidal even though sinusoidal voltage is provided in oc sc test?

eddy current loss in the transformer core is reduced by


How do you test the 11KV HT cables?

The test equipment used to test high voltage cables is a hi-pot test where a high DC voltage is a applied to the cable. This voltage can be from 150% to 200% of the working voltage of the cable.See related links below.


How do you calculate transformer voltage ratio test?

Secondary voltage / primary voltage


What is withstand voltage?

It is the rated test voltage that will not cause insulation breakdown.


How can I test voltage with a multimeter?

To test voltage with a multimeter, set the dial to the voltage setting, connect the black probe to the ground and the red probe to the point where you want to measure the voltage. Read the display for the voltage measurement.


How to test voltage with a multimeter?

To test voltage with a multimeter, set the dial to the voltage setting, connect the red probe to the positive terminal and the black probe to the negative terminal of the circuit or component you want to test. Read the voltage displayed on the multimeter screen.


What machine test hematocrit?

hematocrit machine ......


What is the requirement voltage for P.i test?

insolation resistance test


What is voltage test?

dirct current


What do we use to test Voltage?

A voltmeter


How can design stick-slip machine?

Stick-slip machines are designed to provide more controllable motion than a traditional electric motor. The basic design consists of a motor a control board and a stick-slip mechanism. The motor is used to provide the power to move the stick-slip mechanism while the control board is used to regulate the speed and position of the mechanism. The stick-slip mechanism consists of an elastic element such as a spring or rubber band that is connected to a shaft. When the shaft rotates the elastic element is compressed and then released creating a stick-slip effect. To design a stick-slip machine the following steps must be taken: Choose an appropriate motor and control board. Design the stick-slip mechanism and select an appropriate elastic element. Select the appropriate shaft and bearing system. Integrate the motor control board stick-slip mechanism and shaft into a single system. Test the system and adjust as necessary for optimal performance.By following these steps it is possible to design and build a reliable controllable stick-slip machine.


What is power frequency withstand voltage test?

A test done on a transformer. The voltage at the power frequency is ramped up to verify the transformer is capable of handling the stresses due to switching and natural phenomena (lighting strikes).Withstand Voltage:The voltage which has to be applied to a test object under specified conditions in a "withstand test" is called the "withstand voltage".