0
What else can I help you with?
Difference between flux linkage and flux leakage?
i) leakage flux is those flux which goes through the air and linkage flux is those flux whose go through the cell. ii)leakage flux is the loss at flux but linkage flu is warning flux. iii)leakage flux is cause of eddy current loss and linkage flux is case of copper loss.
What flux percentage is required for wire solder?
The recommended flux percentage for wire solder typically ranges from 2% to 5%. This amount ensures adequate solder flow and wetting to the surfaces being joined, promoting strong and reliable connections. Higher flux percentages can be used in specific applications where more aggressive cleaning is needed, but excessive flux can lead to residues that require cleaning after soldering.
What is the difference between magnetic flux magnetic flux densitymagnetic flux linkage?
light speeeed mofos
Air gap flux is termed as useful flux why?
Basically useful fluke is the flux that flows with in the magnetic circuit of an armature. That is why when there is an air gap the flux enters the armature which makes it useful flux! Hope that answers your question!
Is flux only produce in ac supply or in both ac and dc?
Flux is produced in both AC and DC systems, but the nature of the flux differs. In DC circuits, the magnetic flux is constant, as the current flows in one direction. In AC circuits, the magnetic flux changes direction and magnitude periodically, resulting in a time-varying magnetic field. Thus, while both types of current can produce flux, AC generates a dynamic flux due to its oscillating nature.
What Fluxes are needed for melting brass?
Lemeltic degassing flux
Why is a flux needed for brazing?
You must use flux while brazing because the flux prevents oxides from forming while the metal is heated. The flux also serves the purpose of cleaning any contamination left on the brazing surfaces.
What tools are needed to solder circuit boards?
Soldering iron, solder, flux
What is the need of lamination in transformer?
The laminated plates prevent eddy currents from forming and thus creating unwanted magnetic flux which would counter the flux needed to induce the electric current in the secondary coil
Difference between flux linkage and flux leakage?
i) leakage flux is those flux which goes through the air and linkage flux is those flux whose go through the cell. ii)leakage flux is the loss at flux but linkage flu is warning flux. iii)leakage flux is cause of eddy current loss and linkage flux is case of copper loss.
What is glaze ware in ceramics?
racipe of the glaze for sanitary ware
How tall is Peter Glaze?
Peter Glaze is 5' 5".
When was Billy Glaze born?
Billy Glaze was born in 1944.
Does the process making confectioner's glaze for candies use alcohol?
Confectioner's Glaze, which is also known as resinous glaze, pure food glaze, natural glaze, and pharmacutical glaze, is an alcohol-based solution. When it is created, dried flakes of shellac (which is made from the secretions of female lac bugs) are re-dissolved in denatured alcohol.
Which type of saw flux is susceptible to breaking down into fine particles during circulation?
Granular saw flux is susceptible to breaking down into fine particles during circulation, which can lead to issues such as clogging and blockages in the system. It is important to monitor the condition of the saw flux and replace it if needed to prevent these problems.
Can plumbers solder paste flux be easily removed?
Yes, plumbers solder paste flux can be removed relatively easily, especially when it is still fresh. Using a damp cloth or sponge with warm water can effectively wipe away the flux. For dried flux, a combination of isopropyl alcohol or a commercial flux remover may be needed to fully clean the surface. Always make sure to rinse the area with water afterward to prevent any residue from affecting future work.
What flux percentage is required for wire solder?
The recommended flux percentage for wire solder typically ranges from 2% to 5%. This amount ensures adequate solder flow and wetting to the surfaces being joined, promoting strong and reliable connections. Higher flux percentages can be used in specific applications where more aggressive cleaning is needed, but excessive flux can lead to residues that require cleaning after soldering.
