answersLogoWhite

0

What else can I help you with?

Continue Learning about Engineering

Why cant you use a transformer to increase the voltage of a 60V solar panel?

The output of a solar panel is direct current. Transformers need alternating current to operate.


Difference between step up and step down transformers?

Actually an isolation transformer may be physically the same as a Step up/Step Down transformer. The main difference is in the way they are used. Another difference is that in a normal transformer there will be capacitance between the 2 windings, between the windings and core, between the core and shell, etc. These capacitances bring in high frequency noise from outside, which will be transmitted in the secondary circuit. So [in an isolation transformer] wires are connected between each component, (not direct contact, but with insulation present). This permits a leakage current and eliminates unnecessary capacitance. I could make a start to answer this question. Isolation transformer: is a transformer with two separate windings, the primary and the secondary. There is an electrical isolation between the primary and the secondary. Nearly any type of transformer with two non-connected windings could be considered an "isolation" transformer, in that it electrically isolates the primary voltage from the secondary voltage. There are also transformers with one winding (called auto-transformers) and connections for input and output. If the input is low voltage and the output a higher, then you can say it is a STEP-UP transformer. If the input is high and the output is low, then you can say it is a STEP-DOWN. This type of transformer can not by used where safety is a large factor.


Would you expect to find an alternating or direct current in the secondary coil of a transformer?

An Alternating Voltage is induced in the secondary winding. When connected to an external load, you will have an alternating current.


What is function of capacitor voltage transformer?

The function of a CVT is to provide a secondary voltage to equipment that is a direct ratio of a much higher primary voltage. They can also be used to couple communication signals onto transmission lines.


Why are transformers helpful when using alternating current?

The transformer in the least complex manner can be depicted as a thing that means up or ventures down voltage. It is fundamentally a voltage control gadget that is utilized broadly in the conveyance and transmission of rotating flow power. Trutech Products is a leading Transformer Manufacturers In Pune

Related Questions

What is the difference between a transformer and a rectifer?

A transformer is used to change the value of a voltage applied to the transformer's primary winding to a different voltage value taken from the transformers secondary winding. A rectifier is used to change an alternating current value to a direct current value.


How do you test chopper transformer?

A chopper transformer is a kind of transformer used in an switching power supply.The primary input voltage of it is a Direct current (D.C) unlike any other ordinary step down transformer which uses an Alternating Current (A.C).Chopper transformer uses a switching transistor to produce a secondary voltage..


Why the output voltage from a transformer is zero if a direct current flows through the primary coil?

A transformer relies on AC current flowing through the primary to set up changing magnetic fields in the core. The field flows through the core and in to the secondary of the transformer, generating an AC current. The current must be AC, otherwise the magnetic field in the core of the transformer will saturate. In the same way, the armature of a dynamo or alternator must be moving in order to create a changing magnetic field to create current through the windings.


Why can't a transformer step up the voltage in a direct current?

In order to induce a voltage into the secondary winding of a transformer, there must be a continuously-changing magnetic flux within the magnetic circuit (core) linking the secondary and primary windings. This is only possible if the primary current is also changing -hence the reason why transformers require an a.c. supply. There is an exception to this rule -an automobile's ignition coil is a transformer, supplied from the battery -i.e. a d.c. source. But to provide a changing flux, the d.c. current in the primary winding must be continously switched on and off -in older vehicles, this was done by the contact-breaker driven by the distributor.


What is the difference between a transformer and a rectifier Which are found in a PC power supply?

A transformer is a device that changes the level of an a.c. voltage, while a rectifier is a device that converts alternating current to direct current.


In D.C supply the transformer is not connected why?

In a DC power supply a transformer is connected. The only time there would be no transformer used would be if the DC voltage wanted was 120 VDC. The transformer in the power supply is connected to 120 VAC on the primary side and the secondary side of the transformer is connected to either a half wave or a full wave diode bridge. The voltage out of the diode bridge will be the same output voltage potential as the transformer's secondary voltage but it will be a DC (Direct Current) potential.Reading the question in another way, transformers are not connected in a DC circuit. The reason being is that the transformer operates on a collapsing magnetic field. This field induces a voltage into the secondary side of the transformer. Since the DC circuit does not operate on the principle of a collapsing field except when the circuit is opened, the transformer would not operate as a transformer should..


Why cant you use a transformer to increase the voltage of a 60V solar panel?

The output of a solar panel is direct current. Transformers need alternating current to operate.


Why are most chargers very inefficient?

Voltage must be changed by a transformer, and the alternating current changed to direct current by diodes. Each step has a loss of energy.


How does a current transformer work?

A current transformer is used in high voltage circuits where it is not possible to measure current directly. A CT is a step up transformer with only one turn in primary. There will be as many cores based on the purposes like metering, protection etc. The secondary of a CT should never be kept open circuited bcoz very high flux will be developed in the secondary and hence it may be damaged.


Difference between step up and step down transformers?

Actually an isolation transformer may be physically the same as a Step up/Step Down transformer. The main difference is in the way they are used. Another difference is that in a normal transformer there will be capacitance between the 2 windings, between the windings and core, between the core and shell, etc. These capacitances bring in high frequency noise from outside, which will be transmitted in the secondary circuit. So [in an isolation transformer] wires are connected between each component, (not direct contact, but with insulation present). This permits a leakage current and eliminates unnecessary capacitance. I could make a start to answer this question. Isolation transformer: is a transformer with two separate windings, the primary and the secondary. There is an electrical isolation between the primary and the secondary. Nearly any type of transformer with two non-connected windings could be considered an "isolation" transformer, in that it electrically isolates the primary voltage from the secondary voltage. There are also transformers with one winding (called auto-transformers) and connections for input and output. If the input is low voltage and the output a higher, then you can say it is a STEP-UP transformer. If the input is high and the output is low, then you can say it is a STEP-DOWN. This type of transformer can not by used where safety is a large factor.


Would you expect to find an alternating or direct current in the secondary coil of a transformer?

An Alternating Voltage is induced in the secondary winding. When connected to an external load, you will have an alternating current.


4 What is the difference between a transformer and a rectifier Which are found in a PC power supply?

A rectifier is a device that converts alternating current to direct current. A transformer is a device that changes the ratio fo current to voltage. A rectifier is found in a PC power supply.