0
polarity play essential role in protection purpose if you have done wrong polarity in yours system then protection will operate under normal operation
Further AnswerThe polarity of a single-phase transformer describes the phase relationship of the secondary voltage relative to the primary voltage. Polarity is described as being either 'additive' or 'subtractive'. Knowing a transformer's polarity is one of the essential requirements for paralleling a pair of individual Transformers.
What else can I help you with?
Why terminals of opamp are called as inverting and noninverting?
In an op-amp, an input on the inverting terminal drives the output in the opposite direction, while an input on the non inverting terminal drives the output in the same direction. In a normal closed loop negative feedback configuration, there is feedback from output to inverting input, so that the output becomes a known function of input. So long as you stay within limits, the output will go to whatever value is required to make the inputs be the same.
What would happen if the number of coils on both sides of the transformer were the same?
This is what is known as a 1:1, or ISOLATION Transformer. There is no change to the Voltage or Current of the input, but this does provide a separation between the input and output of the transformer. This separation is sometimes required for safety purposes, especially in a medical environment.
How do you calculate the output voltage of a transformer if kva rating is known?
You can't determine the output voltage of a transformer by knowing kva. Transformers will be marked as to input and output voltages. Some will have multiple input and output voltages. The output voltage depends on the ratio of coil turns between input and output.
Why does the output frequency of a full wave rectifier double that of input frequency?
One cycle of the AC input consists of a positive half-cycle followed be a negative half cycle. The FW rectifier basically reverses the polarity of one of the half-cycles, so there are now two positive pulses per single input cycle, effectively doubling the frequency. Of course the rectifier may be wired for the opposite polarity, with two negative pulses per input cycle, but the same principle applies.
How do you transform transformers?
Open the equipment, unsolder the connections to the transformer, remove the fastenings and remove it. Order a new on on ebay, when it arrives unpack it carefully, place it in the equipment, fasten it in, and resolder the connections. Simple! - (Historikeren 13-07-2014)
What is the basic difference between transistor as an amplifier and a step up transformer?
The output power of an amplifier is greater than its input power, whereas the output power of a transformer is almost the same as its input power. In other words, an amplifier increases acts to increase power, whereas a transformer only increases voltage.
The ratio of coils on the input side of a transformer to coils on the output side is the ratio of the input voltage to the output voltage?
I think you mean 'turns' rather than 'coils' (a coil is made up of a number of turns). The answer is that, yes, the turns ratio is the same as the voltage ratio, for an ideal transformer.
Why terminals of opamp are called as inverting and noninverting?
In an op-amp, an input on the inverting terminal drives the output in the opposite direction, while an input on the non inverting terminal drives the output in the same direction. In a normal closed loop negative feedback configuration, there is feedback from output to inverting input, so that the output becomes a known function of input. So long as you stay within limits, the output will go to whatever value is required to make the inputs be the same.
What would happen if the number of coils on both sides of the transformer were the same?
This is what is known as a 1:1, or ISOLATION Transformer. There is no change to the Voltage or Current of the input, but this does provide a separation between the input and output of the transformer. This separation is sometimes required for safety purposes, especially in a medical environment.
Why the polarity of transformer is important?
a polarity test is a test which use to check the polarity of tranformer.the rision of this test to running the two or more transformer in parallel.like bettry situation or to fin the terminals
How do you calculate the output voltage of a transformer if kva rating is known?
You can't determine the output voltage of a transformer by knowing kva. Transformers will be marked as to input and output voltages. Some will have multiple input and output voltages. The output voltage depends on the ratio of coil turns between input and output.
Can you lower 277v to 240v?
Yes, you can lower the voltage from 277V to 240V using a transformer. A transformer can step down the voltage while maintaining the same frequency. Make sure to select the appropriate transformer with the correct voltage rating for the input and output you need.
Does the input and output frequency of the transformer is the same?
For an 'ideal' transformer operating at full load, the answer is yes. But, 'real' transformers are a little less than 100% efficient so, in practice, the input power will slightly exceed the output power. In most circumstances, for the purpose of calculating primary and secondary currents, we can assume 100% efficiency.
How do you determine whether a table of input output data is a function?
If every input has an output. If two outputs are the same, they must have the same input.
What is the significance of the number of coils on an input side compared to an output side?
For an electrical transformer the ratio of the coils on each side is the same as the ratio for the voltage change.
Does an isolation transformer work from 50 Hz input to 60 Hz output?
Generally speaking, an isolation transformer will work pretty much the same for 50 Hertz as for 60 Hertz. There will be some slight differences, but the frequency is low enough and the the range narrow enough that the transformer will just "do its thing" regardless. Note that the isolation transformer won't change the frequency of the input. An input of 50 Hz or 60 Hz will yield an output of 50 Hz and 60 Hz respectively. No change should be expected.
Is the input in a function table supposed to be the same as the rest of the input?
No, because then the output would be the same as the rest of the output(s).
