because the flushing washer is broken and needs to be replaced, or the inlet washer is broken and the water is over flowing into the pan
there can be many reasons and I will say my thoughts on just a few. 1. your toilet trap of the bowl is clogged with debris (toys, balls, etc) to fix = snake out toilet bowl or if necessary pull toilet bowl and snake backwards threw trap. 2. your tank flush flapper is closing to soon or your tank water level is not at right height to fix = change flapper or adjust water level height 3. your toilet arm before the vent is plugged because of back grade or debris clinging to the side of the drain pipe to test = pull toilet and run toilet water supply full on down threw toilet flange and see if any back flow. 4. your toilet main line is clogged from backgrade,roots,damaged pipe,etc but will let other fixtures slowly drain to test = camera toilet line from toilet flange out to street or septic or if no camera available then fill tub full and lav full and drain both at the same time and look at your lowest fixture trap to see if any back flow exists or open clean outs and if possible to see water flow .
Everything is possible but most likely if it was flushed then it will not get caught in the pipes. ------------ Depending on what you are flushing, it can most certainly get caught in the pipes. Older plumbing cannot handle "modern" things people flush down the toilet, such as feminine hygiene products. These can get caught up in the plumbing, slowly building up and eventually blocking the pipe, creating an UGLY mess. If you take a look at most sit-down commodes you will notice that there are a couple of really sharp turns before the system even enters the floor. At these turns, certain hard things like glasses and cell phones can get caught in the toilet itself.
Sounds like the washing machine discharge is fitted to the main drain in the wrong place and it's discharge is filling your toilet. It's possible there may be something of a blockage just after the toilet, causing a backup. I would try to snake the the pipe from toilet out. You may even have to remove the toilet from the floor and do it there if there is no access underneath (like a basement or a crawlspace). I have snaked main drains from the toilets many times, and it's a pain having to re-re the toilet, but often it's the only way.
Thomas Crapper did not invent the flush toilet, at the time he was just an extremely successful plumber. He had nothing to do at all with the invention .. and the toilet wasnt even invented at the time, it was called the water closet at the time and that was invented by Sir John Harrington. checkk yaaa resourcesss ..
Thomas Crapper did not invent the flush toilet, at the time he was just an extremely successful plumber. He had nothing to do at all with the invention .. and the toilet wasnt even invented at the time, it was called the water closet at the time and that was invented by Sir John Harrington. checkk yaaa resourcesss ..
There could be a problem with the flushing mechanism inside the toilet tank, such as a faulty flapper or a broken chain. This can prevent the toilet from flushing properly even if it's not clogged.
A slow-flushing toilet can be caused by issues with the water pressure, a malfunctioning flapper valve, or mineral buildup in the pipes. It is important to check these factors to determine the cause of the slow flushing and address it accordingly.
There could be several reasons why your toilet is not flushing all the way even if it is not clogged. Some common reasons include issues with the water level in the tank, a problem with the flapper or flush valve, or a blockage in the toilet's trap or drain line. It may be helpful to check these components and make any necessary adjustments or repairs to improve the flushing performance of your toilet.
a toilet is about 50 millon years old even though they were not always flushing but they are 50millon years old kayleigh i don't agree that a toilet is 50millon years i think a toilet is about how long you had it for example:if you had a toilet for 5 years then the toilet is about 5 years
Yes she did but even though she used the old and original way do it in the bucket and chuck it
A slow-flushing toilet can be caused by issues with the water level in the tank, a problem with the flush valve, or a partial blockage in the pipes. It may also be due to mineral buildup or a malfunctioning flapper. Regular maintenance and checking these components can help improve the flushing speed of your toilet.
Your toilet may not be flushing properly due to issues with the flushing mechanism, such as a faulty flapper or a problem with the water level in the tank. It could also be caused by a problem with the water pressure or a blockage in the pipes. It is recommended to check these components and possibly seek professional help to diagnose and fix the issue.
To make people ask questions about it! Actually a toilet flushing on TV is called comic effect. We generally don't expect to hear a flushing toilet on TV, but then we never expected to hear 90% of the remarks that came out of Archie's mouth either! Some might even call it all "potty humor" so the flushing and the yapping were one and the same.
I would intentionally overflow a public toilet by taking the lid off the back, then taking out the thing that covers the hole in the bottom. Then clog the toilet and just wait. The toilet will just flush and flush and flush and flush until it overflows. And then it will keep flushing. You could flood the entire bathroom with no one even knowing!
There could be several reasons why your toilet won't flush properly even if it's not clogged. Some common reasons include issues with the flushing mechanism, a problem with the water level in the tank, or a malfunctioning flapper valve. It's best to check these components and make any necessary repairs or adjustments to ensure proper flushing.
Yes it is very tasty NO R U KIDDING ME WHO WOULD EVEN TRY TO TASTE IT???
Either the toilet is plugged or the sewer line under the toilet is plugged. At this point I would suggest calling in an expert (plumber) to determine the problem. You have not given enough information to say. Sounds like you do not have enough water pressure coming in to wash the waste away. Check out the holes under the lip of the toilet seat to see if they are blocked, causing you to get an inefficient flush. Our new toilet is much better at flushing with lesser amounts of water.