answersLogoWhite

0

Yes. The circuit breaker "does not care" which direction the current comes from. It is capable of protecting the circuit in any case.

User Avatar

Wiki User

13y ago

What else can I help you with?

Continue Learning about Engineering

What is Local breaker back up protection?

Breaker is a protective device that cuts off the electrical circuit in case of fault. The additional breaker can be provided as backup protection locally, which is known as local back up.


What one is better fuse or circuit breaker?

IMO it would be because the circuit breaker has the possibility of going bad and not working (allowing a short to move through the device), but fuses blow (cause a break) no matter what if shorted.


If there are a series of outlets and switches that won't operate in one particular area of your home and there are no breaker switches thrown in the breaker box what else could be causing this problem?

When several outlets are on the same circuit the current comes first from the breaker panel to one outlet where it is connected to a duplex receptacle and/or switch or light, then to the NEXT outlet, light or switch. If a connection was not made properly at any point along the way it can corrode or somehow loose connection back to the breaker panel. If that happens, every outlet DOWNSTREAM will not be working properly. If you cannot track down the problem yourself, you will need to hire an electrician.


Examples of circuit diagram of transfer function?

An battery to light and back or Wires to TV and back.


What circuit breaker acts as a switch creating an circuit when current is too high?

No. circuit breakers are in series with whatever lines they are protecting. They are never put in parallel with the protected loads (this would defeat the purpose). Circuit breakers open resulting in an open circuit / no power to outlets when they trip.

Related Questions

How to wire a circuit breaker properly?

To wire a circuit breaker properly, first turn off the power to the circuit. Then, connect the hot wire to the breaker terminal and the neutral wire to the neutral bus bar. Finally, connect the ground wire to the ground bus bar. Make sure all connections are secure and the breaker is properly seated in the panel before turning the power back on.


How do I properly install a GFCI breaker in my electrical system?

To properly install a GFCI breaker in your electrical system, first turn off the power to the circuit you will be working on. Remove the panel cover and locate the circuit breaker you will be replacing with the GFCI breaker. Disconnect the wires from the old breaker and connect them to the new GFCI breaker according to the manufacturer's instructions. Secure the GFCI breaker in place and replace the panel cover. Turn the power back on and test the GFCI breaker to ensure it is working properly.


How can I add a circuit breaker to my electrical system?

To add a circuit breaker to your electrical system, follow these steps: Turn off the main power supply to your home. Identify the circuit where you want to add the breaker. Install the new circuit breaker in the breaker panel by attaching it to an available slot. Connect the wires from the new circuit to the breaker. Turn the main power supply back on and test the new circuit breaker to ensure it is working properly. It is recommended to consult a licensed electrician for assistance to ensure safety and compliance with electrical codes.


How to install a GFCI breaker in a circuit?

To install a GFCI breaker in a circuit, first turn off the power to the circuit at the main electrical panel. Remove the panel cover and locate the circuit breaker that needs to be replaced with the GFCI breaker. Disconnect the wires from the existing breaker and connect them to the new GFCI breaker according to the manufacturer's instructions. Secure the GFCI breaker in place and replace the panel cover. Turn the power back on and test the GFCI breaker to ensure it is working properly.


How can I reset a motion sensor light?

To reset a motion sensor light, turn off the power to the light at the circuit breaker for a few minutes, then turn it back on. This should reset the sensor and allow it to function properly again.


How do you properly use a breaker box?

To properly use a breaker box, you should first familiarize yourself with the layout and labeling of the circuit breakers. When a circuit trips, locate the corresponding breaker in the box and switch it to the "off" position before turning it back on. It's important to never overload a circuit by plugging in too many devices, as this can cause a fire hazard. If you are unsure about how to safely use a breaker box, consult a licensed electrician for assistance.


Where is the power window circuit breaker on a 2001 town and country?

Hi! The circuit breaker is located at the Back of the Driver's Seat.


What is the process for a Murray breaker replacement?

To replace a Murray breaker, first turn off the power to the circuit. Remove the panel cover and locate the breaker to be replaced. Disconnect the wires from the old breaker and remove it from the panel. Install the new Murray breaker in the same position and reconnect the wires. Finally, turn the power back on and test the circuit to ensure it is working properly.


How do I properly add a breaker to a panel?

To properly add a breaker to a panel, first turn off the main power switch. Remove the panel cover and identify a free slot for the new breaker. Connect the breaker to the panel's bus bar and then connect the circuit wire to the breaker. Secure the breaker in place and replace the panel cover. Finally, turn the main power switch back on.


How do you install a GFCI breaker?

To install a GFCI breaker, first turn off the power to the circuit at the main electrical panel. Remove the panel cover and locate the circuit breaker you want to replace with the GFCI breaker. Disconnect the wires from the existing breaker and connect them to the new GFCI breaker according to the manufacturer's instructions. Secure the GFCI breaker in place and replace the panel cover. Turn the power back on and test the GFCI breaker to ensure it is working properly.


How to install a 50 amp breaker in a circuit panel?

To install a 50 amp breaker in a circuit panel, first turn off the power to the panel. Remove the panel cover and locate an open slot for the breaker. Connect the hot wire to the breaker, the neutral wire to the neutral bar, and the ground wire to the ground bar. Secure the breaker in place and replace the panel cover. Turn the power back on and test the circuit to ensure it is working properly.


How to install a 30 amp breaker in a circuit panel?

To install a 30 amp breaker in a circuit panel, first turn off the power to the panel. Remove the panel cover and locate an open slot for the new breaker. Connect the hot wire to the breaker, the neutral wire to the neutral bus bar, and the ground wire to the ground bus bar. Insert the breaker into the slot and secure it in place. Turn the power back on and test the circuit to ensure it is working properly.