sentence of summarize
It means to tell a lie or an exaggeration in a story.
The sound of a vowel depends on the dialect of the language you are speaking, as well as context. In this case "bow" isn't very informative, if you think of the sentence "The girl with a bow in her hair took a bow from the bow of a boat, before shooting an arrow with her bow." Most dialects identify two or three sounds for the 'ow' in that sentence. In the general American dialect, it could make what is identified as a long o, similar to the vowel sounds in "no" or "goat", or it could make a very different sound, like the vowel sound in "now".
i supose a long bow which is the type you practice on in school cause thhey're cheap
It can be confusing to use a homograph, because a female archer might not wear her bow in her hair, and shipbuilders do not give a polite bow to a ship.A homograph is a word written the same way as another word but having a different meaning.(Example: Bow-hair, weapon and Bow-front of a ship, or to bend at the waist)
There are two pronunciations of the spelling "bow."To take a bow (bend at the waist) is an OU/OW sound, pronounced to rhyme with cow.The long O sound is seen in the weapon (bow and arrow), or a decorative ribbon. This form of bow rhymes with low and grow.
30" is not a draw weight, it is a draw length. It is the length of the draw from the bow to the string when the bow is drawn.
It means to tell a lie or an exaggeration in a story.
The draw weight should be marked on the bow. You cannot go any higher than the marked draw weight unless your bow has removable limbs, then you could buy limbs with a higher draw weight. You will ruin the bow if you use it with a higher draw rate.
the arrow you should choose depends on the draw lenght of the archer. when you go to an archery shop, take your bow and they will give you an arrow with a ruler on it, you draw the arrow in the bow and the shop owner will tell you how long you draw the arrow.
Bow it, meaning to draw a bow across the strings.
If it is a compound bow, the type of bow with the pulleys or "wheels" at the ends of the bowlimbs, there should be some way to adjust the draw-length of the bow itself; it may be best to consult someone at an archery shop for the best way to make such an adjustment. When using a Traditional bow -- a recurve or longbow, or other non-compound type -- the only "adjustment" is to simply pull the string back (in this case) to 27 inches; reducing the draw-length in this way also reduces the effective draw-weight of the bow. Also, when using a Traditional bow, and the archer has a longer draw-length than the bow is rated for (i.e., the archer's draw-length is 30 inches, but the bow is rated at 27 inches), it is always advisable to make sure the bow is designed to withstand the longer draw-length. Failure to do so can result in the catastrophic failure of the bow, and possibly serious injury to the archer. Increasing the draw-length of a traditional bow will also increase the effective draw-weight of the bow.
"Draw weight" is a measure of the strength required to draw a bow as well as the force it imparts on the arrows it shoots. It is usually measured in pounds.
the draw lengthon a nova s7 bow can be adjusted between 27-29 inches
The Bow hand, the other is called the draw hand.
The general rule of thumb is that one inch of draw length will increase your speed by approximately 10 fps. This will vary from bow to bow and depends a lot on the draw length and poundage being changed.
Draw the bow to full draw and hold it. Have your assistant place a nail in the small round hole in the bottom of each pulley wheel and then slowly let the pressure off of the bow string. Unhook the looped bowstring from the metal string connectors and set aside. Slide the connectors up and away from the bow limbs and pull them out of the pulley wheels. Move the connectors to a new hole or position on the wheels (a higher hole if you want the draw length shorter or a lower hole if you want the draw length longer). Reconnect the string to the metal string connectors and draw the bow to full draw again. Have your assistant pull the nails out of the pulley wheels and then let the bow down slowly. This process can also be performed by using a bow press to depress the bow's limbs and then changing the draw length in the same manner.
They don't really break. Make sure you're holding the button long enough to get a full draw on the bow...