answersLogoWhite

0

You can saddle branches of the same size or smaller onto headers at various degrees. There are typical 16-division layout; and also a 64-division layout to calculate information for mitered ells and rolling offsets.

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

What is the formula to layout pipe saddles for joining pipe at angles?

I edited and uploaded a program I wrote to calculate pipe saddle layout, pipe miter layout, and to calculate running offsets for piping runs. I have used similar programs in the past to get information to pipe fitters. I am using and evaluating a conversion program that limits what I can upload during the free trial period; so the sheets may be a bit awkward to use....let me know. Those of you who use the method of dividing a pipe in 16-divisions will note I have added 64-division points should you want to use these; the 64-divisions would be better to use if you were making a saddle template for larger pipe or for a saddle with a shallow angle. (I moved this to 'www.pipesaddlelayout.com) Let me know if it works for you or what seems confusing. Dave


How do you layout any lateral on pipe?

drawing for lateral pipe


How do you make a pipe saddle?

Take a look at the Related Link below; there is a page that calculates the layout lengths to be used when laying out saddles. You can saddle branches of the same size or smaller onto headers at various degrees. The page shows the information typical 16-division layout; and also a 64-division layout for reference or for when you want to make a template that is more accurate. There are also pages to calculate information for mitered ells and rolling offsets.


What is the formula to make a pipe saddle?

90


Which tool you use in pipe 60 deg layout for pipe fitting?

Swansons square


How does a saddle drain work in plumbing systems?

A saddle drain is a type of fitting that is used to connect a smaller pipe to a larger pipe in a plumbing system. It is typically used to create a branch connection for a new fixture, such as a sink or a toilet. The saddle drain is installed by cutting a hole in the larger pipe, attaching the saddle fitting over the hole, and then connecting the smaller pipe to the fitting. This allows wastewater to flow from the new fixture into the main plumbing system.


What is the formula to layout pipe miters?

There is no exact formula to lay out pipe miters, but there is information that must be known to calculate the layout. This includes the diameter, wall thickness, angle, and offset.


How can I properly install a drain saddle for my plumbing system?

To properly install a drain saddle for your plumbing system, follow these steps: Turn off the water supply to the area where you will be installing the drain saddle. Locate the drain pipe where you want to install the saddle and clean the area around it. Measure the diameter of the drain pipe and choose a drain saddle that fits. Position the drain saddle over the drain pipe and mark the holes for the screws. Drill pilot holes for the screws and secure the drain saddle in place. Connect the drain saddle to the plumbing system according to the manufacturer's instructions. Turn the water supply back on and check for any leaks. It is important to follow the manufacturer's instructions and local plumbing codes when installing a drain saddle to ensure proper installation and functionality.


How can I install a saddle valve for my water supply line?

To install a saddle valve for your water supply line, first turn off the water supply. Then, locate a suitable spot on the pipe where the valve can be attached. Use a pipe cutter to cut a small section of the pipe. Place the saddle valve over the cut section and tighten the screws to secure it in place. Turn the valve handle to pierce the pipe and create a connection. Finally, turn the water supply back on and check for any leaks.


What is a saddle valve and how is it used in plumbing systems?

A saddle valve is a type of valve used in plumbing systems to connect a water supply line to a pipe. It is typically used to supply water to appliances like ice makers or water filters. The saddle valve is attached by clamping onto the pipe and piercing it to create a connection for the water supply line.


What is the layout of the kitchen sink pipes diagram?

The kitchen sink pipes diagram typically shows the layout of the pipes underneath the sink, including the drain pipe, trap, and vent pipe. The drain pipe carries water and waste away from the sink, while the trap prevents sewer gases from entering the kitchen. The vent pipe allows air to enter the system to help with drainage.


How can I extend a sink drain pipe to accommodate a longer distance or different layout in my plumbing system?

To extend a sink drain pipe for a longer distance or different layout in your plumbing system, you can use a PVC extension pipe and fittings. Measure the distance needed, cut the extension pipe to size, and connect it to the existing drain pipe using appropriate fittings and PVC cement. Make sure to secure the connections properly to prevent leaks.