0
Can you change your led display in your opel vectra b 1997 in to multi information display?
yes you can but will need to make new wires to got to speedo signal and fuel gauge if the wires are not there. would need a gray plug, This is the wire code for gray plug.
grey connector info, in the brackets is the equivalent earlier MID pin info (Y=Yellow con and B=Black con)
Pin1(Y2) - Brown - To Chassis (0V)
Pin2(Y3) - Blue/White stripe - Outside temp sensor
Pin3(Y4)- Blue - Outside temp sensor
Pin4(Y5) - Black - To F15 (15A)
Pin5(Y1) - Red - To F12 (20A)
Pin6 - Green - RPM signal, needs to be conecter to dash.
Pin7(Y7) - Grey/Yellow stripe - Instrument Illumination (dimmer controled)
Pin8(Y8) - Red/Grey(white) Stripe - Radio (aerial power feed i.e. Radio on indication)
Pin9(Y9) - Brown/White Stripe - Radio Serial Interface
Pin10(Y10) - Brown/White Stripe - Radio Serial Interface
Pin11(Y11) - Brown/White Stripe - Radio Serial Interface
Pin12(B8) - Blue/Black Stripe - Fuel level sender
Pin13(B11) - Brown/Grey Stripe - Oil level sensor
Pin14(Y14) - Brown/White Stripe - To pin 8 of diag connector (to support programming)
Pin15(Y15) - Black/Yellow stripe - To check control
Pin16(Y16) - Black - To F2 (15A)
Pin17(Y17) - White/Green stripe - To check control
Pin18(Y18) - Black/Yellow stripe - To check control
Pin19(Y19) - Yellow/Red stripe - To brake pad wear sensors
Pin20 - NC
Pin21(Y23) - Grey - To Auto transmission
Pin22(B10) - Brown/Yellow Stripe - Washer Level sensor
Pin23(B5) - Brown/White Stripe - Computer stalk buttons
Pin24(B6) - Brown/Red Stripe - Computer stalk buttons
Pin25 - NC
Pin26(Y12) - Blue/red stripe - Speed signal (from ABS controller)
Pin27(B9) - Black/Brown Stripe - ECU signal
Pin28(B3) - Brown/Blue stripe - Coolant level sensor
Pin29 - Black/Violet Stripe - To Hid lighting
Pin30 - To Diesel fuel pump (X20DTH only)
What else can I help you with?
How do you change a bulb in the multi function display unit of a 307?
You can change a bulb in the multi function display unit of a 307 by first making sure that the lamp is turned off. Then unscrew the bulb and remove it from the lamp.
Can some one help Replaced bulb in multi function display on 99 vectra it blow and now got no dash lights at all can someone help please?
check the fuse if it is bad change it, if its not the fuse you will have to remove the gauge cluster and replace the bulb that way.
How do you change my multi function display for Fahrenheit to Celsius for temp?
To switch the temperature unit on your multi function display from Fahrenheit to Celsius, consult your vehicle's user manual for specific instructions. Typically, you would navigate through the settings menu on the display panel using the buttons or touchscreen to find the temperature unit setting and select Celsius.
Is the only way to replace multi info display on a Vectra 20 CDX 1997 through a dealer?
no not really you can physically replace the unit easy enough but you may need the main dealer to use their tech programmer to program too the car!
What computer terms contain the prefix multi?
Multi-layer DVD drive. Multi-speed CD drive. Multi-resolution display.
How do you change the clock on a pioneer deh-p3000ib car stereo?
Setting the clock Use these instructions to set the clock. 1 Use MULTI-CONTROL to select CLOCK SET in the initial setting menu. Refer to Adjusting initial settings on this page. 2 Press MULTI-CONTROL to display the setting mode. # Press DISP/BACK/SCRL to return to the previous display. 3 Press MULTI-CONTROL to select the segment of the clock display you wish to set. Each time you press MULTI-CONTROL, one segment of the clock display is selected. Hour—Minute As you select segments of the clock display, the selected segment blinks.
How to change toyota estima 2006 language?
To change the language on a 2006 Toyota Estima, start by turning on the vehicle and accessing the multi-information display. Use the control buttons on the steering wheel or dashboard to navigate to the "Settings" or "Setup" menu. Look for an option labeled "Language" or similar, and select your desired language from the list. Confirm the selection, and the display language should update accordingly.
How do you change the date and time on Peugeot 406 Estate LX?
Hold down the LEFT button next to the multi-function display for a couple of seconds. The display should now start flashing. Press the Left button briefly to scroll through the display options and the RIGHT button to change the currently flashing item.
Does the droid x have a keyboard?
No, it has a multi-touch touchscreen display
How do you reset the message to change oil on 2008 highlander?
# Turn off the engine with the trip meter A reading shown. # With your foot 'off' the brake, press the "Engine Start Stop" button once The radio display will light and radio will come on, but instrument gauges do not. # Then, while pressing the trip meter reset button, push the "ENGINE START STOP" button or engine switch ON (keeping your foot 'off' the brake, Don't start engine, just push the start button until radio and display comes on #Without multi-information displayContinue to press and hold the trip meter reset button until the trip meter displays 000000. With multi-information displayContinue to press and hold the trip meter reset button until "COMPLETE" appears on the multi-information display
Multi function display frozen on your peugeot 406?
If the multi-function display is frozen on a Peugeot 406, the computer may have to be reset. Unhook the positive cable on the batter for a few minutes.
What does mfd mean in car interior lights?
multi function display
