0
MY ADVICE:take it to the volkswagon dealer...reallybut if you are like me and like a chalange...this is my experiencefirst off my plastic lever wos broken off i didnt have a clue how this worked exept that just about every other car in the world bult after Y2K you pull the cap off the back and repace the bulb.EZ when i came to this site looking for answers all i found wos this unanswerd question that's where i learnd about the lever that controles the tightening mec.for the whole assembly.remember i had no instruction at all so i may have taken xtra steps first i took the battery out.next the air cleaner,the tube that goes from the air cleaner to front of car,and the battery box.VERY FRUSTRATING i played with the lever on the right side ov the car to see how it worked it moved easy so i sprayed a little pb blaster on the plastic got my big needle nose plyers went under to grab the plastic where the handle wos...wala the whole assembly fell out .somhow i don't think this is how they do it at the shope linning it back up(after changing the bulb)wos trikky but it went together.all and all it tok 4 or5 hours i don't know about you but i would have perferd to pay somone to do it and gone fishing SO that may not be how you are supposed to do it but it is how i did it
What else can I help you with?
Where is hood release on 2006 pathfinder?
The hood release is located behind the plastic panel beneath the steering wheel, all the down and behind. You will see a small plastic lever that you squeeze towards the drivers seat.
How do you replace the headlight bulb located on a 1999 Pontiac Grand Prix?
With the hood open remove the (2) two headlamp assembly bolts from the upper fascia support. Slide the headlamp assembly outward enough to release the headlamp bracket tabs from the slots in the upper fascia support. (to release the tabs from the slots on the passenger side lens move the assembly to the left when facing the engine, and when doing the drivers side lens shift the assembly to the right ) Position the headlamp assembly away from the vehicle body to access the electrical connector. Disconnect the electrical connector from the headlamp assembly. Remove the headlamp assembly from the vehicle. If you wish to change the halogen bulb: Disconnect the electrical connector from the headlamp bulb/socket. Remove the headlamp bulb/socket retainer ring from the headlamp, by turning counterclockwise. Remove the headlamp bulb/socket from the headlamp assembly. Hope this helps. "G" These instructions are similar from around '96 to '03 grand prix model years all trim levels.
How do you replace the headlight bulb located on a 1995 Pontiac Grand Prix?
With the hood open remove the (2) two headlamp assembly bolts from the upper fascia support. Slide the headlamp assembly outward enough to release the headlamp bracket tabs from the slots in the upper fascia support. (to release the tabs from the slots on the passenger side lens move the assembly to the left when facing the engine, and when doing the drivers side lens shift the assembly to the right ) Position the headlamp assembly away from the vehicle body to access the electrical connector. Disconnect the electrical connector from the headlamp assembly. Remove the headlamp assembly from the vehicle. If you wish to change the halogen bulb: Disconnect the electrical connector from the headlamp bulb/socket. Remove the headlamp bulb/socket retainer ring from the headlamp, by turning counterclockwise. Remove the headlamp bulb/socket from the headlamp assembly. Hope this helps. "G" These instructions are similar from around '96 to '03 grand prix model years all trim levels.
How do you change a headlight in a 2001 Pontiac grand prix?
With the hood open remove the (2) two headlamp assembly bolts from the upper fascia support. Slide the headlamp assembly outward enough to release the headlamp bracket tabs from the slots in the upper fascia support. (to release the tabs from the slots on the passenger side lens move the assembly to the left when facing the engine, and when doing the drivers side lens shift the assembly to the right ) Position the headlamp assembly away from the vehicle body to access the electrical connector. Disconnect the electrical connector from the headlamp assembly. Remove the headlamp assembly from the vehicle. If you wish to change the halogen bulb: Disconnect the electrical connector from the headlamp bulb/socket. Remove the headlamp bulb/socket retainer ring from the headlamp, by turning counterclockwise. Remove the headlamp bulb/socket from the headlamp assembly. . "G" These instructions are similar from around '96 to '03 grand prix model years all trim levels.
How do you change a headlamp 2002 buick rendezvous?
1. Open the hood.2. Remove the thumb screw from the back of the headlamp.3. Release the headlamp retainer by lifting up.4. Pull the headlamp straight forward, to release the ball stud from the grommet.5. Remove the headlamp from the upper fascia support.6. Disconnect the electrical connector from the headlamp.7. Remove the bulb(s) from the headlamp by rotating counterclockwise.8. Release the headlamp trim tabs from the headlamp, if required.9. Remove the headlamp trim from the headlamp, pulling to release the adhesive tape.10. Clean adhesive from the headlamp trim and headlamp using 3M™ adhesive remover P/N 8984, or equivalent.To install:1. Install new adhesive tape 3M® P/N 6382 or equivalent to the headlamp trim, if necessary.2. Position the headlamp trim to the headlamp, if removed.3. Install the headlamp trim to the headlamp, pressing until end tabs are fully seated.4. Install the headlamp bulb(s) to the headlamp by rotating clockwise.5. Connect the electrical connector to the headlamp.6. Position the headlamp to the upper fascia support.7. Press the headlamp into the upper fascia support until the ball stud is fully seated.8. Install the thumb screw to the rear of the headlamp.9. Engage the headlamp vertical retainer, by sliding downward until fully seated.10. Check the headlamp aim, if a new headlamp was installed, or if service or repairs in the front end area were made.11. Close the hood.
How do you replace the headlight bulb on a 2006 Nissan Altima?
HEADLAMP (OUTER SIDE), FOR LOW BEAM (XENON) Disconnect negative battery cable. Remove headlamp. Turn the plastic cap counterclockwise and unlock it. Turn the bulb socket counterclockwise to unlock it. Unlock the retaining spring and remove the bulb from the headlamp. Install in reverse order of removal. CAUTION: After installing the bulb, be sure to install the plastic cap securely to ensure watertightness. HEADLAMP (OUTER SIDE), FOR LOW BEAM (HALOGEN) Disconnect negative battery cable. Remove headlamp. Turn the plastic cap counterclockwise and unlock it. Disconnect the electrical connectors from the bulb terminals. Unlock the retaining spring and remove the bulb from the headlamp. Install in reverse order of removal. CAUTION: After installing the bulb, be sure to install the plastic cap securely to ensure watertightness. HEADLAMP (INNER SIDE), FOR HIGH BEAM Remove headlamp. Turn the bulb counterclockwise to remove it. Installation is reverse order of removal. Removal and Installation REMOVAL Remove the front fascia. Refer to"FRONT BUMPER" . Ensure lighting switch is OFF. Disconnect the negative battery cable. Remove the headlamp mounting bolts. Pull the headlamp toward the front of the vehicle, disconnect connectors, and remove from vehicle. INSTALLATION Install in the reverse order of removal, taking care of the following point. Headlamp mounting bolts: Tightening Torque: 4.4 - 6.4 N.m (0.45 - 0.65 kg-m, 39 - 56 in-lb) DISASSEMBLY Turn the low beam plastic cap counterclockwise to unlock and remove it. Turn the bulb socket counterclockwise to unlock and remove it (xenon). Disconnect the electrical connectors from the bulb terminals (halogen). Unlock the retaining springs and remove the low beam bulb. Release the ballast (ignitor) and remove from the plastic cap (xenon). Turn the high beam lamp socket counter clockwise to unlock and remove it. Turn the front turn signal lamp bulb socket counterclockwise and unlock it. Remove the front turn signal lamp bulb from its socket. ASSEMBLY Assemble in the reverse order of disassembly.
Where are the fuses in a 1997 ford aerostar?
Drivers side under dash in a small black plastic box right behind the hood release.
How do you replace the headlight bulb located on a 2004 Pontiac Grand Am?
1. Open the hood. 2. Remove the front air deflector. 3. Apply light pressure to the headlamp lens to hold the headlamp assembly in place while disconnecting the retainers. 4. Lift up the headlamp assembly retainers to release. Important: Note the location and position of the headlamp adjuster retainers and the locator tab. 5. Remove the headlamp assembly, pulling straight forward from the headlamp mounting panel. 6. Disconnect the wiring harness from the headlamp assembly. 7. Rotate the headlamp bulb/socket counterclockwise to release. 8. Remove the headlamp bulb/socket from the headlamp assembly, if required. There are (2) pull up clip retainers that hold the headlamp assembly in place...Both of these must be removed for the headlamp assembly to be pulled forward...:)
How do you change the front signal light bulb on a 1997 Pontiac Grand Prix?
With the hood open remove the (2) two headlamp assembly bolts from the upper fascia support. Slide the headlamp assembly outward enough to release the headlamp bracket tabs from the slots in the upper fascia support. Position the headlamp assembly away from the vehicle body to access the electrical connector. Disconnect the electrical connector from the headlamp assembly. Remove the headlamp assembly from the vehicle. This gives you access to the turn signal and headlight. If you wish to change the halogen bulb: Disconnect the electrical connector from the turn signal bulb/socket. Remove the turn signal bulb/socket retainer ring from the assembly, by turning counterclockwise. Remove the turnsignal bulb/socket from the assembly. to re-assemble simply do the reverse. . "G"
How do you replace the headlight bulb located on a 2002 Ford E-250?
For all Ford Late model Econoline vans E150, E250, E350; you will need a pair of pliers or similar tool. With the hood open, above each headlamp on the left and right there are metal tabs. Using the pliers pull these tabs up to release the headlamp assembly. It may take some finessing but eventually the headlamp will come free. With the headlamp removed, you can now replace the bulb. Rotate the plastic ring to release the old bulb and disconnect the wires. Put the attachment ring on the new bulb, attach the wires and reverse the process.
How do you open the bonnet on 2011 Ford Fiesta?
Open the passenger door, the bonnet release is just below the glove box, on the left hand side plastic trim. There is a yellow safety catch in between the drivers side front headlamp unit and the Ford badge, move that to one side (spring loaded) and the bonnet should lift up. (UK model, right hand drive)
What are the release dates for Avengers Assemble - 2010 Baywatch?
Avengers Assemble - 2010 Baywatch was released on: USA: 3 January 2014
