First, Open the trunk and locate the general area where the taillight is located and wired, IE Right or left. Then look on the inside wall of the trunk, there should be a small area that can be removed, like a small cover. Remove the cover, this will allow you to reach inside Once inside locate a small thumb wheel type knob, un loosen it, righty tighty, lefty loosey. Once this is loosen, remove the knob. Now return to the outside part of the tail light, find an area where the plastic rim of the light cover meets the metal of the car, place your fingernail or small screwdriver in between the cover and car, gently pry enough to get a grip on the light cover and pull away from the car. The whole taillight cover should now be removed. Now remove the bad bulb, pushing down on the bulb and turning a 1/4 turn left. Replace with new bulb, first pushing down then 1/4 turn right.
* Remove the rear inside trunk finishing panel to access the taillight housing mounting nuts * Free the grommet for the taillight electrical harness and the three taillight housing nuts then pull off the taillight housing * Rotate the bulb socket counterclockwise and pull it out of the taillight housing * To remove the bulb from the socket pull it straight out.To install a new bulb in the socket push it straight into the socket until it stops
* Remove the rear inside trunk finishing panel to access the taillight housing mounting nuts * Free the grommet for the taillight electrical harness and the three taillight housing nuts then pull off the taillight housing * Rotate the bulb socket counterclockwise and pull it out of the taillight housing * To remove the bulb from the socket pull it straight out.To install a new bulb in the socket push it straight into the socket until it stops
To change the left rear marker light bulb on a 2008 Lexus RX 350, first, open the rear hatch and locate the taillight assembly. Remove the screws or fasteners holding the taillight in place, then gently pull the assembly out. Twist the bulb socket counterclockwise to remove it, replace the old bulb with a new one, and reassemble the taillight by reversing the steps. Ensure everything is securely fastened before closing the hatch.
To change the rear turn signal light on a Dodge Caliber, first, open the rear hatch and locate the taillight assembly. Remove the screws or clips holding the taillight in place, then gently pull the assembly out. Twist the bulb socket counterclockwise to remove it, replace the old bulb with a new one, and reassemble the taillight by reversing the steps. Test the new bulb to ensure it’s functioning properly before closing the hatch.
* Remove the rear inside trunk finishing panel to access the taillight housing mounting nuts * Free the grommet for the taillight electrical harness and the three taillight housing nuts then pull off the taillight housing * Rotate the bulb socket counterclockwise and pull it out of the taillight housing * To remove the bulb from the socket pull it straight out.To install a new bulb in the socket push it straight into the socket until it stops
* Remove the rear inside trunk finishing panel to access the taillight housing mounting nuts * Free the grommet for the taillight electrical harness and the three taillight housing nuts then pull off the taillight housing * Rotate the bulb socket counterclockwise and pull it out of the taillight housing * To remove the bulb from the socket pull it straight out.To install a new bulb in the socket push it straight into the socket until it stops
* Remove the rear inside trunk finishing panel to access the taillight housing mounting nuts * Free the grommet for the taillight electrical harness and the three taillight housing nuts then pull off the taillight housing * Rotate the bulb socket counterclockwise and pull it out of the taillight housing * To remove the bulb from the socket pull it straight out.To install a new bulb in the socket push it straight into the socket until it stops
To change the rear bulb on a 2008 Hyundai Tiburon, start by opening the trunk and locating the access panel behind the taillight assembly. Remove the screws or clips securing the panel, then gently pull it away to expose the taillight. Twist the bulb socket counterclockwise to remove it, replace the burnt bulb, and reassemble the components in reverse order. Finally, test the new bulb to ensure it’s working properly.
* Remove the rear inside trunk finishing panel to access the taillight housing mounting nuts * Free the grommet for the taillight electrical harness and the three taillight housing nuts then pull off the taillight housing * Rotate the bulb socket counterclockwise and pull it out of the taillight housing * To remove the bulb from the socket pull it straight out.To install a new bulb in the socket push it straight into the socket until it stops
* Remove the rear inside trunk finishing panel to access the taillight housing mounting nuts * Free the grommet for the taillight electrical harness and the three taillight housing nuts then pull off the taillight housing * Rotate the bulb socket counterclockwise and pull it out of the taillight housing * To remove the bulb from the socket pull it straight out.To install a new bulb in the socket push it straight into the socket until it stops
To change the brake bulb on a 1994 Isuzu Rodeo, first, open the rear hatch and locate the taillight assembly. Remove the screws or clips securing the taillight, then gently pull it out to access the bulb sockets. Twist the socket counterclockwise to remove it, then replace the old bulb with a new one, ensuring it's securely in place. Reassemble the taillight and test the brake lights before closing everything up.
* Remove the rear inside trunk finishing panel to access the taillight housing mounting nuts * Free the grommet for the taillight electrical harness and the three taillight housing nuts then pull off the taillight housing * Rotate the bulb socket counterclockwise and pull it out of the taillight housing * To remove the bulb from the socket pull it straight out.To install a new bulb in the socket push it straight into the socket until it stops