0
1. Make sure all doors, hood and trunk are closed.
2. Open the trunk door.
3. Open the drivers door and sit in the drivers seat.
4. Close the drivers door.
5. Turn ignition switch to on and off 5 times ending in off.(do not start the car turn to just before starting)
Your alarm light will turn on and the siren on the alarm will chirp to let you know it is ready.
(this can also be used to test if you have the alarm)
6. Open the drivers door stay in the seat close the drivers door.
7. Press any button on the remote. The light will flash to indicate your remote has been programmed.
8. Repeat steps 6 & 7 to program any other remotes, up to 4 remotes a car.
9. To exit program mode open drivers door leave the door open. Close the trunk lid and close the drivers door the
siren should chirp again and the red light will shut off. Test your remotes to make sure they work right.
What else can I help you with?
Will headliner in 98 BMW 528i fit in a 97 528i?
It depends on what options the 98 and 97 have. If you get the vin # on both cars and call BMW they can tell you for sure if it will fit.
Where is the transmission dipstick in 98 BMW 528i?
The transmission dipstick in a 98 BMW 528i is on the driver's side of the transmission pan. Make sure you are parked in a level spot before you check it.
How many miles should a 98 BMW 528i have?
I know this is not your question, but I bought a 2000 528i with 68K miles in almost perfect condition. So with a 1998 I really would not but anything with more than 90K miles...
How do you program a viper alarm remote?
reprogram 98 ford expedition with viper 600 alarm
98 BMW 528i codes listing it's entirety and process of resetting them?
To retrieve the diagnostic trouble codes (DTCs) from a 1998 BMW 528i, you'll need an OBD-II scanner compatible with BMW or the proprietary BMW diagnostic tool. Once connected, you can read the codes by following the prompts on the scanner. To reset the codes, you can either clear them using the scanner or disconnect the car’s battery for about 15 minutes. However, be aware that disconnecting the battery may also reset other systems and settings in the vehicle.
Where is the brake fluid reservoir on a 98 BMW 528i?
On a 1998 BMW 528i, the brake fluid reservoir is located on the driver's side of the engine bay, near the back of the engine compartment. It is typically a translucent plastic container with a cap labeled for brake fluid. To check or add brake fluid, make sure the engine is off and allow the engine to cool down before opening the reservoir.
Where is the dip stick on a 98 BMW 740 il?
98 BMW maps for dipstick on car free
Does anyone know which alarm system Toyota dealers installed on 2000 4Runner Limiteds More specifically which remotes work with this alarm and how does one reprogram the remotes?
my 98 4runner alarm system does not seem to be working if i used the alarm to open the door it will not open Try E-bay for some answers search '98 4 runner remotes some gives you the info and the program.
Will discoNNECTING the battery reset my abs light on my 98 bmw 528i?
Disconnecting the battery may reset the ABS light on your 1998 BMW 528i temporarily, but it won't necessarily fix the underlying issue that triggered the light. The ABS light indicates a problem with the anti-lock braking system, and simply resetting it won't address any faults in the components or sensors. It's best to diagnose the problem using a scan tool to read the error codes before disconnecting the battery.
Will a hard top 01 BMW Z3 fit 98 BMW Z3?
no
How do you Disable car alarm for 98 Ford Explorer sport?
How do you Disable car alarm for 98 ford explorer sport?Read more: How_do_you_Disable_car_alarm_for_98_ford_explorer_sport
Where is the O2 sensor located on your 98 BMW 528i?
On a 1998 BMW 528i, the O2 (oxygen) sensors are located in two places: one is upstream (pre-catalytic converter) and the other is downstream (post-catalytic converter). The upstream sensor is typically found in the exhaust manifold or just before the catalytic converter, while the downstream sensor is located after the catalytic converter in the exhaust system. To access them, you may need to lift the vehicle and work from underneath or remove some engine covers. Always ensure the engine is cool before attempting any maintenance.
