with the switch off, press and hold the odometer button. Turn the switch on, and the odometer will be in insp mode. mode. Press the odometer button until the indicator shows --- . Turn the switch off and the lamp should be reset.
The easiest way to reset the timing belt indicator lamp in your Toyota automobile is to remove the fuse for the indicator lamp. Keep the fuse out for approximately 30 seconds. Put the fuse back in and the indicator light should be off.
To reset your malfunction indicator lamp start your car then you hire fps russia to blow up your piece of terrible car and buy a new one simple actually.feces
Resetting the Service reminder indicator (SRI), model years -2001 The service reminder indicator (SRI) informs the driver that it is time for the car to be serviced. The lamp remains lit for 120 seconds when the ignition is switched on. Note! If the lamp flashes, it may be because one of the service parameters has not been programmed. Proceed as follows to reset the service reminder indicator (SRI): -Ignition position I -Press and hold in the reset button for the trip odometer -Ignition position II -The service reminder indicator (SRI) starts flashing when the reset button for the trip odometer has been pressed for 10 seconds -Release the reset button for the trip odometer within 5 seconds. The instrument gives an audible signal when resetting has succeeded. Note! If the trip meter reset button is not released within 5 seconds the indicator is not reset. However the indicator will stop flashing. Resetting the service reminder indicator (SRI), model years 2002- The service reminder indicator (SRI) informs the driver that it is time for the car to be serviced. The text message is displayed for 120 s each time the ignition is switched on. Proceed as follows to reset the service reminder indicator (SRI): -Ignition position I -Press and hold in the reset button for the trip odometer -Ignition position II. Note! Turn the key to position II within 2 seconds. -Hold the reset button for the trip meter pressed in until the original value has been reset. Note! For all vehicles from the 2003 model year a general yellow lamp will light when the reset button must be released. -Release the reset button for the trip odometer within 4 seconds. The instrument gives an audible signal when resetting has succeeded -If the trip meter is already reset the reset button should be held in for a minimum of 10 seconds and a maximum of 14 seconds. Note! If the reset button for the trip odometer is not released within 4 seconds, the service reminder indicator (SRI) is not reset.
There is no reset for taillamp failure relay. If there is a fault the message will continue to be displayed www.lextechautomotivellc.com
To reset the brake lamp indicator on a 2000 Acura TL, first ensure that the brake lights are functioning properly. If they are, disconnect the negative terminal of the battery for about 10 minutes to reset the system. Reconnect the battery and check if the indicator has cleared. If the light remains on, it may indicate a more serious issue that requires further diagnosis.
its on your rear end and armpit loser hair
according to autodata service lamp can only be reset using suitable diagnostic computer Dr.Pedro VolksWagen service technician
Resetting the service reminder indicator (SRI), model years 2002- The service reminder indicator (SRI) informs the driver that it is time for the car to be serviced. The text message is displayed for 120 s each time the ignition is switched on. Proceed as follows to reset the service reminder indicator (SRI): -Ignition position I -Press and hold in the reset button for the trip odometer -Ignition position II. Note! Turn the key to position II within 2 seconds. -Hold the reset button for the trip meter pressed in until the original value has been reset. Note! For all vehicles from the 2003 model year a general yellow lamp will light when the reset button must be released. -Release the reset button for the trip odometer within 4 seconds. The instrument gives an audible signal when resetting has succeeded -If the trip meter is already reset the reset button should be held in for a minimum of 10 seconds and a maximum of 14 seconds. Note! If the reset button for the trip odometer is not released within 4 seconds, the service reminder indicator (SRI) is not reset." Resetting the service reminder indicator (SRI), model years 2002- The service reminder indicator (SRI) informs the driver that it is time for the car to be serviced. The text message is displayed for 120 s each time the ignition is switched on. Proceed as follows to reset the service reminder indicator (SRI): -Ignition position I -Press and hold in the reset button for the trip odometer -Ignition position II. Note! Turn the key to position II within 2 seconds. -Hold the reset button for the trip meter pressed in until the original value has been reset. Note! For all vehicles from the 2003 model year a general yellow lamp will light when the reset button must be released. -Release the reset button for the trip odometer within 4 seconds. The instrument gives an audible signal when resetting has succeeded -If the trip meter is already reset the reset button should be held in for a minimum of 10 seconds and a maximum of 14 seconds. Note! If the reset button for the trip odometer is not released within 4 seconds, the service reminder indicator (SRI) is not reset." Resetting the service reminder indicator (SRI), model years 2002- The service reminder indicator (SRI) informs the driver that it is time for the car to be serviced. The text message is displayed for 120 s each time the ignition is switched on. Proceed as follows to reset the service reminder indicator (SRI): -Ignition position I -Press and hold in the reset button for the trip odometer -Ignition position II. Note! Turn the key to position II within 2 seconds. -Hold the reset button for the trip meter pressed in until the original value has been reset. Note! For all vehicles from the 2003 model year a general yellow lamp will light when the reset button must be released. -Release the reset button for the trip odometer within 4 seconds. The instrument gives an audible signal when resetting has succeeded -If the trip meter is already reset the reset button should be held in for a minimum of 10 seconds and a maximum of 14 seconds. Note! If the reset button for the trip odometer is not released within 4 seconds, the service reminder indicator (SRI) is not reset."
> Resetting service reminder: 1. Press and hold rear fog lamp switch 2. Turn ignition on, do not start engine 3. Release rear fog lamp switch 4. Press and hold trip button (end of left side stalk) 5. Press and hold rear fog lamp switch 6. See "Resetting Service Light" message in message center
Proceed as follows to reset the service reminder indicator of your : Ignition position I Press and hold in the reset button for the trip odometer Turn the key to position II within 2 seconds. Keep holding the reset button for the trip meter pressed in until a yellow lamp lights then the reset button must be released. Release the reset button for the trip odometer within 4 seconds. The instrument gives an audible signal when resetting has succeeded If the trip meter is already reset the reset button should be held in for a minimum of 10 seconds and a maximum of 14 seconds. If the reset button for the trip odometer is not released within 4 seconds and before the light stops flashing, the service reminder indicator is not reset.
There's no great ''trade secret'' as to how to reset the service indicator lamp on most Vauxhall's, simply refer to pages in the Owner's Handbook! For reference of those interested in such matters, but who might not have access to an owner's manual, this is the procedure to follow: Vauxhall service reset * Turn Ignition Off * Hold Trip Reset In * Turn Ignition On Still Holding * Trip Reset wait for three dashes * Turn off Ignition * Turn on Ignition to confirm To the best of my knowledge, the above service light reset procedure applicable to most Vauxhalls HOPE THIS SAVES YOU PAYING FOR INFORMATION!!!!!!!!!!!!!!!!!!!! ;-)
The best way is to use the users manual. If this does not help you, then it is a good idea to visit a mechanic.