answersLogoWhite

0

at the back of the engine, screwed into the exhaust manifold

User Avatar

Wiki User

14y ago

What else can I help you with?

Related Questions

How do you change catalytic converters 1999 Ford Escort zx2?

Unbolt Lambda probe, unbolt cat from rear and front system. Install new cat, install Lambda probe in new cat. done.


Why would your L reg legacy stop when the cat fell and how can you get it to start and go again?

There's a thing called a Lambda probe, or Lambda sensor that's mounted to the catalytic converter. The engine control system needs that one to know if the engine is getting enough fuel or not, so it won't run w/o it. You need a new cat and a new lambda (at least) to get it running again.


Will oxygen sensor in exhaust system stick and drain battery?

most modern lambda sensors have a heating element and relay which can drain the battery. To test, disconnect the sensor ,if found to be the cause buy new lambda sensor and check wiring.


How do you change lambda sensor on2006 clio?

To change the lambda sensor on a 2006 Renault Clio, first, ensure the engine is cool and disconnect the battery. Locate the lambda sensor, usually found on the exhaust pipe; use a lambda sensor socket or wrench to unscrew it. Install the new sensor in the same position, ensuring a proper seal, and reconnect the battery. Finally, start the engine to check for any warning lights and ensure proper function.


How do you change lambda sensor Audi tt?

To change the lambda sensor on an Audi TT, first, ensure the engine is cool and disconnect the negative battery terminal for safety. Locate the lambda sensor, typically situated in the exhaust system; you may need to remove any heat shields for access. Disconnect the electrical connector and use a lambda sensor socket or wrench to unscrew the old sensor. Install the new sensor, reconnect the electrical plug, and reattach any removed components before reconnecting the battery.


How do I change the O2 sensor 1 in bank 1 in a 1999 Daewoo Lanos?

iirc sensor 1 bank1 is a pre cat lambda sendor. Its the first one visiable on the manifold/downpipe from the engine before the catalytic converter. you just undo the multiplug and remove the sensor with a spanner turning the whole sensor anticlockwise, screw in the new sensor, tighten it up and reattach multiplug.


How do you fit lambda sensor vectra c?

To fit a lambda sensor on a Vauxhall Vectra C, first ensure the engine is cool and disconnect the battery. Locate the lambda sensor, which is typically situated in the exhaust system, and use an appropriate socket to unscrew it. Install the new sensor by threading it into place, ensuring it's securely tightened, and reconnect the electrical connector. Finally, reconnect the battery and check for any error codes or leaks.


VW Beetle 2.0 camshaft senors 2001?

Show me how to replace the camshaft position sensor on a 2000 volkswagen new beetle


How do you change a lambda sensor on a peugeot 306?

To change a lambda sensor on a Peugeot 306, first disconnect the battery to ensure safety. Locate the lambda sensor, which is typically positioned on the exhaust system near the catalytic converter; you may need to lift the car for better access. Use a suitable socket or wrench to unscrew the old sensor and carefully disconnect the wiring plug. Install the new sensor by reversing the process, ensuring it is securely tightened and the electrical connection is properly attached before reconnecting the battery.


Where is the air intake temperature sensor on a 2003 Volkswagen New beetle 2.0L engine located?

It is important to know the location of a car's parts. The 2003 Volkswagen New beetle air intake temperature sensor is built into the mass airflow sensor.Ê


How do you replace a lambda sensor on a Renault clio 2004?

To replace the lambda sensor on a 2004 Renault Clio, first, ensure the engine is cool and disconnect the battery. Locate the lambda sensor, typically found on the exhaust manifold or downstream in the exhaust system, and unplug the electrical connector. Use a suitable socket or wrench to unscrew the old sensor and replace it with the new one, ensuring it's tightened properly. Finally, reconnect the electrical connector and the battery before starting the engine to check for proper operation.


How do you replace a catalytic converter in an Audi A4 98?

Unbolt lambda sensor, unbolt cat at front and rear flange. Drop it down, discard, and install new cat. Bolts are quite likely to be seized in place, so be prepared to cut them out and replace. Some luck might be had with nut splitters, penetrating oils and suchlike.