The phenomenon you're experiencing, known as "dieseling" or "run-on," typically occurs when the engine continues to receive fuel and air after the ignition is turned off. This can be caused by several factors, including carbon buildup in the combustion chamber, a faulty ignition switch, or issues with the fuel system. Additionally, if the engine is running too hot or if the idle speed is too high, it may continue to operate briefly after the key is removed. It's advisable to have a mechanic check the engine to diagnose and resolve the issue.
because the french are sh*t at electrics
If you are having an issue with the immobilizer on a Peugeot 307 HDI, you need to recode your key. To do this put the key into the ignition and turn to the on position, hold the Lock button on the key for 10 seconds, take the key out of the ignition, and then test to see if the car starts after another 10 seconds.
Switch ignition off, press & hold the button to the left of the speedo while switching ignition on. After 10 seconds the new interval will appear in the display accompanied by a beep. Release the button. Switch ignition off.
To change the ignition key on a Peugeot 106, you'll first need to ensure you have the new key programmed to the vehicle's immobilizer system. Insert the old key into the ignition and turn it to the "On" position without starting the engine. Within a few seconds, turn the old key back to "Off" and remove it, then insert the new key and turn it to "On." This should allow the new key to be recognized by the vehicle's system. If you encounter issues, consult a professional locksmith or a Peugeot dealer for assistance.
Oh, dude, resetting the radio in a Peugeot 307 is like a walk in the park. Just turn the ignition on, hold down the 'AS' button for a few seconds until it beeps, and then enter your radio code. It's as easy as making toast, man.
Switch ignition OFF Press and hold in button between speedo & water temp Switch ignition ON (not start) Keep button in for 10 seconds Display will now read zero and "spanner" symbol gone Relaese button & switch ignition OFF
On the bottom left of the instrument cluster, is a button marked 0. Switch ignition on and immediately press the button. Switch ignition off. Press and hold the button while switching the ignition on. After 10 seconds, the new interval will appear, accompanied by a beep. Release button. Switch ignition off.
The duration of IPW Ignition is 3600.0 seconds.
If the battery has been out of the key fob for too long the fob loses its program and the car will not start. Peugeot will try to charge £48 for a reprogram but you can get around this by: - 1) Turn on the ignition 2) Hold down the close button for a few seconds 3) Turn off the ignition and remove the key 4) Start the car The above can be found on page 19 or 20 of the 407 user manual
the the ignition to on but not the engine running and pres the gass pedal 3 times withing 5 seconds and it will go away
Turn the ignition on but engine not running. Press the tripometer button and hold for ten seconds, a menu will appear showing the same symbols on your I drive. Scroll to the right symbol the press the button for three seconds this will reset the required function. Press the button again for three seconds to confirm changes, then ignition off and all should be OK.
(a) Switch OFF the radio & Ignition (b) Turn Ignition ON (Position II) (c) The airbag warning light will stay on for 7 seconds and then switch off - as soon as it does turn OFF the ignition (within 1 second of the light switching off) (d) Wait at least 5 seconds (e) Repeat steps (a) to (c) two more times - this is important to make sure it registers with different modules in the car (f) Turn ON ignition, wait 2 seconds (g) Switch OFF Ignition (Position 0) and wait 1 second (h) Switch ignition back ON. (i) Airbag light should now remain unlit as long as the fault(s) causing are also addressed