0
What else can I help you with?
What are coterminal angles?
Coterminal Angles are two angles in standard position with the same terminal side.
What is the angle when the terminal side of an angle in standard position lies along one of the axes?
Quadrantal angle
What Angle function is standard position to the?
The angle function in standard position is typically measured from the positive x-axis in a counterclockwise direction. An angle is in standard position when its vertex is at the origin of a coordinate plane, and its initial side lies along the positive x-axis. The terminal side of the angle is determined by the angle's measure, and it can be positive or negative, depending on the direction of rotation.
What is a co-terminal?
Co-terminal angles are angles that share the same terminal side when drawn in standard position, differing only by an integer multiple of 360 degrees (or 2π radians). For example, 30 degrees and 390 degrees are co-terminal because if you add 360 degrees to 30, you arrive at 390. This concept is useful in trigonometry, as it allows for simplification of angle measurements and calculations. In essence, co-terminal angles represent the same direction or position on the unit circle.
Find degree of angle in standard position formed by rotating the terminal side by 22 over 45 of a circle?
22/45 of 360 degrees = 22/45 x 360 = 7920/45 = 176 degrees
Does the live wire from the ignition key go to the bat terminal and a live wire from the starter go to the tach terminal on a hei distributor for 350 Chevy in a boat with non standard wiring?
You do need a switched live to the bat terminal, but not to the tach terminal. The tach terminal is the negative side of the coil, the bat terminal is the positive side of the coil. Normally the tach terminal is for the green wire from the tach.
What side is the positive terminal for the 2007 boulevard s40?
In a 2007 Boulevard S40 the positive terminal of a battery is located where the red terminal is. Another characteristic that separates it from the negative side is the width of the positive terminal.
What is the plug wire placement on the ignition cap and standard firing on a 1977 Chevy 350Ci?
1,8,4,3,6,5,7,2 is the standard firing sequence on ALL small and bigblock Chevy V8's.Do you have points or electronic?If electronic,see the part on the cap of HEI ignitions that sticks out from the left?Clockwise,# 1 cylinder terminal is the second one(approximately the 5'oclock position,same with points ignitions)Start with cylinder # 1.This is the cylinder on the drivers side.Very first one.Connect plug wire from Terminal # 1 to cylinder # 1.Next in line is cylinder # 8(approximately the 7 o'clock position).Connect plug wire from terminal # 8 to cylinder # 8. On the left side of engine are cylinders 1,3,5,7.On the right side of engine are cylinders 2,4,6,8.Continue the sequence above clockwise.If you have points,MSD,Crane,etc.,dont forget to connect your coil to the terminal in the top of the cap.
What side dishes goes with steak?
normally salad or lettuce with a lemon derssing with feta cheese and many tomatotes
Find tan if an angle in standard position and the point with coordinates negative twelve and positive five lies n the terminal side of the angle?
If you draw this angle in a coordinate system, a right triangle is formed in the second quadrant, with length legs 12 and 5 units. If you label with O the angle that is formed by the terminal side and y-axis, you have tan O = 12/5 and O = tan-1 12/5 = 67.38 degrees Thus, the given angle has a measure of 157.38 degrees (90 + 67.38).
Where is number 1 terminal on the distributor cap on a ford 5.8 Windsor and where should it point?
The marked # 1 position on the distributor cap faces to the rear and slightly towards the drivers side
What figure is formed by a terminal side and an initial side?
An angle on the coordinate plane
