0
What else can I help you with?
What carb upgrade for Weber 34 DMTR?
A popular carburetor upgrade for the Weber 34 DMTR is the Weber 40 DCOE or 45 DCOE, which offers improved airflow and performance for higher output engines. These dual-carb setups provide better throttle response and can enhance the overall driving experience. Additionally, tuning options are more extensive with DCOE series, allowing for better customization to suit specific engine needs. When upgrading, ensure that your intake manifold and other components are compatible with the new carburetor for optimal performance.
How old is otzi the iceman?
Otzi, The Iceman, Is About 5,000 Years Old...If the iceman were to be alive today then he would have been 5,300 years old.But when he died he was 45-50 years old.
Where is route 45 in Pokemon Crystal?
Route 45 is south of Blackthorn City.
What Level Does Metang Evolve in pokemon black?
Metang evolves into a Metagross at level 45.
What actors and actresses appeared in 16 45 - 1999?
The cast of 16 45 - 1999 includes: Alessandro Haber
What carb upgrade for Weber 34 DMTR?
A popular carburetor upgrade for the Weber 34 DMTR is the Weber 40 DCOE or 45 DCOE, which offers improved airflow and performance for higher output engines. These dual-carb setups provide better throttle response and can enhance the overall driving experience. Additionally, tuning options are more extensive with DCOE series, allowing for better customization to suit specific engine needs. When upgrading, ensure that your intake manifold and other components are compatible with the new carburetor for optimal performance.
Want to install cv carb on 75 sportster what to jet at?
Start with a 45 pilot and 170 main. If you get carb farts or other problems, check for a vacume leak first....
What is recommended fuel pressure Chevy?
what year? fuel inj.?carb.? if it's fuel inj. it's 40-45 lbs. if it's got a carb. it's 7-14lbs
What is the fuel pressure for Lt1?
Earlier carb type LT1 6 1/2-7 psi Fuel injected Vettes and Camaro aprox 45 psi.
Can you turn a toilet 45 degrees?
UH HUH if you adjust the floor flange YOU can even install it backwards if you have room behind it
How do you cut a 45-degree angle with a miter saw?
To cut a 45-degree angle with a miter saw, adjust the saw blade to a 45-degree angle, place the material against the fence, and carefully make the cut following the marked line.
What would be the best spark plug gap for a 73 SB 350 with a 50k volt HEI unit edelbrock rpm intake and EDL 600 cfm carb?
0.045 45 thousands
How to cut a 45 degree angle with a table saw?
To cut a 45-degree angle with a table saw, adjust the blade to a 45-degree angle, set the fence to the desired width, and carefully guide the wood through the saw blade using a miter gauge or sled for accuracy and safety.
How do you adjust timing from 45 BTDC back to 0 like its suspose to be?
Year, make, model and engine size would help us help you.
How do you adjust the headlights on a Rover 45?
To adjust the headlights on a Rover 45, first park the vehicle on a level surface facing a wall about 25 feet away. Measure the height of the headlight beams and mark this height on the wall. Then, use a screwdriver to turn the adjustment screws located on the back of the headlight assembly, aligning the beams with the marked height. Ensure both headlights are adjusted symmetrically for optimal visibility.
How can you accurately cut a 45-degree angle with a hand saw?
To accurately cut a 45-degree angle with a hand saw, you can use a miter box. Place the wood in the miter box and adjust the saw to a 45-degree angle. Hold the saw firmly and make the cut following the guide of the miter box for a precise angle.
How do you adjust a carburetor for a 1984 Toyota Corolla?
The idle adjustment screw is on the driver`s side , towards the back of the carburetor , it`s about an inch and a half long , pointing upwards at a 45 degree angle and has a turn valve type knob on it . On the other side of the carb. is a fast idle screw adjustment w/ a screw type head on it , at the bottom of the carb. pointing towards the front of the vechicle , but all I know of this screw is the name . An auto repair manual for each type vehicle is your best bet ! There`s a download repair manual file of one in " 84 Toyota Corolla DLX 1.6L.com " , listings . I know that will help , too ! Wishing you luck ! Jero .
