0
There is no such thing, 30 watts is 30 watts. "Line in" is normally about 1v peak - to - peak. So if your 30 watt amp has a "line out", no problem. An amp can be modified to have a "line out". Similarly, an amp can be modified to accept larger inputs without damage. However, driving an amp straight from the normal output of an amp, although possible, is fraught with danger and expensive consequence and should be avoided at all costs
What else can I help you with?
How a triode works as basic amplifier?
A triode works as a basic amplifier by the use of radio waves. The radio waves produce a heat that is amplified.
What can you use a signal generator to find?
To trace a problem in an amplifier. Send in a signal and trace its' path.
What type of light bulbs do modern table lamps use?
Modern table lamps use all sorts of different light bulbs. Most commonly one can find standard 20 watt to 250 watt light bulbs in modern table lamps.
What is the 6x4 tube use for in a hammond organ?
its 1 of 8 tubes from the Hammond Preamp AO-28 (in B3, C3, A-100 console models) Its a rectifier tube. you can read here, what a rectifier is: http://en.wikipedia.org/wiki/Rectifier
Can you use a higher watt light bulb instead of a lower watt light bulb E.g. A lamp uses 9w light bulbs can I use a 13 watt one?
9w to 13w is not a big jump, but you need to check the fuse rating, which will have been chosen to limit the current to a safe level for the wiring, to see if the extra current is still within the fuse rating. Is this in an auto? If at 12v the current will rise from 0.75 amp to 1.08 amp. You should also check the lamp holder to see if there is a power limit stamped or printed on it.
Can I use a preamp into a speaker?
You need a power amplifier in between.
Can you use a 600 watt amp with a 500 watt subwoffer?
Yes, you can use a 600 watt amplifier with a 500 watt subwoofer. It is important to ensure that the amplifier's output power does not exceed the subwoofer's power handling capability to avoid damaging the subwoofer. It is also recommended to properly set the gain levels on the amplifier to match the subwoofer's power handling.
Can you use a 5800 watt amplifier with 2 12 inch 1400 watt woofers?
Yes, you can use a 5800-watt amplifier with two 12-inch 1400-watt woofers, but it's important to match the amplifier's output to the speakers' power handling to avoid damage. If the amplifier's power significantly exceeds the woofers' ratings, you may need to be cautious with volume levels to prevent overpowering the woofers. Additionally, ensure that the impedance of the woofers matches the amplifier's output specifications for optimal performance.
Can you use 30 watt speaker to 60 watt amplifier?
Yes, you can use a 30-watt speaker with a 60-watt amplifier. The amplifier's higher wattage provides more power than the speaker is rated for, but as long as you don’t push the amplifier to its maximum output, the setup can work without damaging the speaker. However, it’s important to avoid excessive volume levels, as this could potentially lead to speaker distortion or damage. Always ensure to match volume levels appropriately to protect the speaker.
Can you use a 8 ohm 400 watt speaker on a 4 ohm 350 watt amp to play bass?
Yes, you can use an 8-ohm 400-watt speaker with a 4-ohm 350-watt amplifier to play bass. The speaker will receive less power from the amp, resulting in lower volume, but it won't damage the speaker or the amplifier. Just ensure that the overall impedance of your setup matches the amplifier's specifications to prevent any potential issues.
Can you use a400 watt speaker with150 watt amp?
You can, but the problem is your speakers will not give their optimal sound quality because your Amplifier is too weak for the speakers. So,buy an amplifier with an output power rating high then 400w.
Will a 1200 watt amplifier blow out a 1000 watt subwoofer?
Technically, yes. Practically, no. Amplifiers and speakers are rated by the maximum amount of power (and at what impedance) they can handle. A 1200 watt amplifier will eventually destroy a 1000 watt speaker if it is operated at maximum power. In normal use, however, you rarely even get close to maximum rating.
Can you run a 500 watt amplifier at low volume on a 140 watt ac converter?
Yes, you can run a 500 watt amplifier at low volume on a 140 watt AC converter. The power consumption of the amplifier will depend on the volume level it is set to. As long as the amplifier is not drawing more power than what the converter can supply, you should be able to use them together safely. Keep an eye on the power indicator on the converter to ensure it's not being overloaded.
Can you use 2x500 watt subs on a 600 watt amp?
Absolutely!! If you turn up the gain too much, the speakers will smoke. You can use it at a lower level
Can you plug cables from the microphone jack to an amplifier?
Yes, you can plug cables from a microphone jack to an amplifier, but it's important to use the correct type of cable and ensure compatibility. Microphone jacks typically use low-level signals, and if you connect them directly to a standard amplifier input, you may experience low volume or distortion. It's advisable to use a microphone preamp to boost the signal before connecting to the amplifier for optimal sound quality.
How do you test the output of an acoustic guitar preamp?
To test the output of an acoustic guitar preamp you may use output tubes to test. This will test the preamp voltage.
Could a phono drive be used as an amplifier for a mixing desk?
It's not clear what you mean by "phono drive". If you are asking about using a phono preamp as a microphone or instrument preamp and sending the output of the preamp to the mixer, you will find that the phono preamp has two problems:First, it does not have anything close to flat frequency response. Phono preamps are designed with a strong equalization curve, which compensates for the EQ that is used when high-fidelity recordings are mastered. You will get lots of bass and no highs if you try to run a mic or instrument signal through a phono preamp.Second, you may find that it does not have a lot of headroom. A phono preamp is sensitive and a microphone or instrument could drive it into saturation.For the same reasons, you certainly cannot use a phono preamp as a line-level amplifier in a mixer.If you happen to be asking if you can use a Mod Squad or McCormack Phono Drive as a preamp for a turntable and run the output of the Phono Drive (as line level) into a DJ mixing desk, then the answer is yes, that should work quite nicely (even though the Phono Drive is, in my opinion, an absurdly overpriced piece of gear).
