0
What else can I help you with?
Is a transaction log permanent or temporary?
permanent
Rusty can cut a log into 3 pieces in 20 minutes at that rate how long will it take him to cut another such log into 6 pieces?
50 minutes.
Explain how to use a Doyle log scale?
The Doyle Log Scale, developed around 1825, is based on a mathematical formula and is widely used throughout the southern United States. This rule allows for a saw kerf of 5/16 inch (most circular mills). Because of this, the Doyle Rule is somewhat inconsistent; it underestimates small logs and overestimates large logs. To use a Doyle Log Scale measure the diameter of the log (not including the bark) and the length. Then using the Doyle scale you can calculate the board foot content of a log.
What is the resistance force when a wedge of an axle splits a log?
The resistance force is the log. It trys to stop the wedge of the axe. The effort force of the swinging axe helps it break through the log, breaking through its resistance.
Logs sometimes float vertically in a lake because one end has become water-logged and denser than the other. What is the average density of a uniform-diameter log that floats with 54.0 of its length a?
To find the average density of a uniform-diameter log floating with 54.0% of its length submerged, we can use Archimedes' principle. The density of the log must be equal to the density of the water multiplied by the fraction of the log that is submerged. Assuming the density of water is approximately 1,000 kg/m³, the average density of the log can be calculated as follows: [ \text{Density of log} = \text{Density of water} \times \text{Fraction submerged} = 1000 , \text{kg/m}^3 \times 0.54 \approx 540 , \text{kg/m}^3. ] Thus, the average density of the log is about 540 kg/m³.
What is a floater in a sinker in terms of density?
A floater is an object that has a lower density than the fluid it is in, allowing it to remain on the surface or float. In contrast, a sinker has a higher density than the fluid, causing it to sink. This principle is governed by Archimedes' principle, which states that an object will float or sink based on the relationship between its density and the density of the fluid.
Why is a sinker necessary in determining the lifting effect of water?
A sinker is necessary to determine the lifting effect of water because it helps to counteract the buoyant force exerted by the water on the object. By adding a sinker, you can measure the force required to keep the object submerged, which allows you to calculate the buoyant force acting on the object.
What quantities do you need to know in order to determine the amount of heat released by the lead sinker in cooling to the final temperature?
mass of water, initial temp of the water, final temp of water after the hot sinker is put into the water, the temp of the hot sinker (if it is heated in separate boiling water, the temperature of the water) and the specific heat of water ( 1 cal/g degree C)
When was George Sinker born?
George Sinker was born in 1900.
When did George Sinker die?
George Sinker died in 1986.
When was Spy Sinker created?
Spy Sinker was created in 1990.
When did John Sinker die?
John Sinker died in 1936.
When was John Sinker born?
John Sinker was born in 1874.
How do you determine the value of logarithmic decrement?
You can, instead, find the log of the ratio. Thus: log(A) - log(B) = log(A/B)
Why there is a need for a sinker in determining the specific gravity of objects lighter than water?
A sinker is needed to help submerge the lighter object in water to accurately measure the change in water level caused by its displacement. This helps determine the volume of the object, which is necessary to calculate its specific gravity. Without the sinker, the object may float and not displace enough water for an accurate measurement.
What is an ark-floater?
An ark-floater is an aged or experienced actor.
What is the greek word for floater?
The Greek word for "Floater" is "επιπλέων".
