answersLogoWhite

0

I pick up the large pieces by hand, then sweep everything I can into a dustpan. After that I run the vacuum over the area.

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

What precautions should be taken to safely clean up a broken glass table?

To safely clean up a broken glass table, wear thick gloves to protect your hands from sharp edges. Use a broom and dustpan to carefully sweep up the larger pieces of glass. Then, use a damp paper towel or cloth to pick up the smaller shards. Dispose of the glass in a sturdy container and seal it tightly before throwing it away. Finally, thoroughly clean the area with a vacuum cleaner or mop to ensure all glass fragments are removed.


How do you clean broken glass out of my dishwasher?

Before I begin, I would like to state that I, personally, wouldn't clean broken glass out of YOUR dishwasher. I think your grammar is a bigger problem than your broken glass. You should have been consistent, one of the following would have been much better: 1) How do you clean broken glass out of your dishwasher? 2) How do I clean broken glass out of my dishwasher? 3) How does one clean broken glass out of a dishwasher? To answer: Remove the racks, pick up the big pieces CAREFULLY with your fingers, use a damp stack of a few paper towels for the small pieces (which you can throw directly in the trash after the small pieces stick to it), then run a cycle or two to wash the tiny leftover pieces away.


What precautions should be taken to safely clean up broken glass on a desk?

To safely clean up broken glass on a desk, wear gloves and shoes to protect yourself from cuts. Use a broom and dustpan to carefully sweep up the glass, then use a damp paper towel to pick up any remaining small pieces. Dispose of the glass in a secure container and thoroughly clean the area with a wet cloth to ensure all shards are removed.


What safety precautions should be taken when handling a broken lightbulb in mouth?

Do not handle a broken lightbulb with your mouth. Use gloves and a broom to clean up the broken glass, and dispose of it properly in a sealed container. Avoid touching the broken glass with your bare hands to prevent injury.


Is it okay to vacuum up broken lightbulb pieces?

The EPA encourages you to never use a vacuum cleaner to clean up a broken fluorescent light.They recommend that you pick up as much as possible by hand and then use the sticky side of a piece of tape to pick up what you can't get manually.


How do you clean up a broken lava lamp?

If a lava lamp breaks, it is important to wear gloves and use paper towels to carefully clean up the broken glass and liquid. Make sure to dispose of the broken glass in a secure container and clean the area thoroughly with soap and water to remove any residue. Avoid direct contact with the liquid to prevent skin irritation.


Use immediate in a sentence?

When I dropped the jar of jam, the immediate need was to clean up the broken glass, then to wash up the sticky jam.


What can you use to clean inside a car?

A vacuum


How can make a vacuum in glass?

To create a vacuum in a glass container, you can use a vacuum pump to remove air molecules from within the container. Place the glass container on a vacuum pump, turn it on to create a low-pressure environment, and then seal the container to maintain the vacuum inside. This will remove most of the air molecules from the container, creating a vacuum.


How can I create a broken glass effect in Photoshop?

To create a broken glass effect in Photoshop, you can use the "Crystallize" filter to distort the image and make it look like shattered glass. You can also use the "Glass" filter to add a reflective and transparent effect to the broken areas. Experiment with different blending modes and opacity levels to achieve the desired broken glass effect.


What is the best type of glue to use for repairing a broken window glass?

The best type of glue to use for repairing a broken window glass is a clear silicone adhesive.


How do you replace car window?

You call a professional if it is a windshield or glued perimeter part and if it is a door glass you can locate and remove the screws that hold the panel on and then pry the panel from the door frame and then clear the glass in the rubber tracks on the sides with a screwdriver or remove and clear and re-install the side/top track rubbers then remove either the track at the bottom of the glass and clean it and use urethane glue to push the new glass into or (mattering upon the year and model) remove the tabs that attach the glass to the regulator/track that were from the old broken glass then install the new glass which should have the tabs on there. vacuum door inside's bottom and slam to loosen glass to fall and vacuum again and your done. -awautoglass.com