answersLogoWhite

0

Wet Mount Slide Steps

1. Place a sample on the slide.

2.Using a pipette, place a drop of water on the specimen. Then place on edge of the cover slip over the sample and carefully lower the cover slip into place using a toothpick or equivalent.

*This method will help prevent air bubbles from being trapped under the cover slip. Your objective is to have sufficient water to fill the space between cover slip and slide. If there is too much water, the cover slip will slide around. Take a piece of paper towel and hold it close to one edge of the cover slip. This will draw out some water. If too dry, add a drop of water beside the cover slip. Practice this until you get used to it.

Staining Steps

  1. Prepare a wet mount slide.
  2. Collect a drop of stain with an eye dropper or pipette.
  3. Put a drop of stain on an outer edge of your cover slide.
  4. Place a piece of napkin or paper towel against the opposite side of your cover slip, right up against the edge. This will help draw the stain under the cover and across the specimen.
  5. You may need to add another drop to ensure complete coverage.
  6. The slide is now ready for viewing.
Source: Microscope.com
User Avatar

Wiki User

10y ago

What else can I help you with?

Related Questions

Which staining procedure uses heat to drive the stain in?

The heat-based staining procedure is called heat fixation. In this process, heat is used to adhere the specimen to the slide, allowing it to withstand the subsequent staining and washing steps without washing away.


What are the steps of the wet mount?

the five steps to making a wet mount slide is 1.use a flat glass slide to prepare a wt mount slide 2.suck up a few drops of water from your liquid specimen into a medicaine dropper 3.pick up the wet mount slide on the 2 outer sides of the slides 4.place the specimen your using into the water 5.place the top cover slips on the top of the water with the specimen in it (: (: (: (: (: (: (: (: (: (:


What are the steps to make a wet mount slide?

You need the bottom of the the slide, the you put a specimen on it. After put a drop of water on it then put the cover and apply pressure.


Can you prepare microscope slides for cell division?

Yes, preparing microscope slides for observing cell division involves fixing cells to a slide, staining the cells to make them visible under the microscope, and then covering the sample with a coverslip to protect it. The process may include steps such as cell fixation, permeabilization, staining with specific dyes or antibodies, and mounting with a mounting medium. It is important to carefully follow a protocol to ensure accurate visualization of cell division.


What would happen if no heat fixing were done?

If no heat fixing was done to a slide with a specimen on it, it would be rinsed off with the gram staining procedure. Heat fixing the specimen does kill specimen but it also locks it in place.


Function of heat-fix in gram staining?

Heat-fixing in gram staining serves to adhere bacterial cells to the slide, making them more resistant to washing off during the staining process. It also helps to kill the bacteria, allowing them to take up the crystal violet stain more effectively. Additionally, heat-fixing can alter the permeability of the bacterial cell wall, aiding in the retention of the stain through subsequent decolorization steps.


What are the steps involved in preparing a wet mount of a specimen?

To prepare a wet mount of a specimen, first, place a small drop of liquid (like water or a suitable medium) on a clean microscope slide. Next, using a pair of tweezers, carefully place the specimen in the drop. Then, gently lower a coverslip at an angle over the specimen to avoid air bubbles. Finally, observe the specimen under a microscope, adjusting the focus as needed.


How many steps will you have to climb at The Verruckt water slide in Kansas City?

You will have to climb 264 steps to ride The Verruckt slide.


What if you forgot to heat fix your slide?

If you forget to heat fix your slide your bacterial sample will be lost with the next wash step. So if you are doing a Gram stain when you add the crystal violet the liquid will mix with the bacteria, and when you wash later in the protocol the bacteria will wash away with the stains.


Preparing for a dry fast?

Preparing for a dry fast involves taking certain steps before beginning your fast


When preparing to pass what steps should you follow?

hi guys


When creating a wet mount the microorganism is free to move on the slide?

No, the microorganism needs to be heat fixed onto the slide so it doesn't wash away with all the wash steps. The wet part refers to the liquid that is placed on the fixed cells before the cover slip is put on.