0
29 mm equates to approximately 1.14 inches.
Direct Conversion Formula
29
mm
*
1 in
25.4 mm
=
1.141732283
in
Wiki User
∙ 11y ago
Wiki User
∙ 10y ago1.141732283 in
Direct Conversion Formula 29 mm*
1 in
25.4 mm
=
1.141732283 in
Wiki User
∙ 10y ago1.141732283 in
Direct Conversion Formula 29 mm*
1 in
25.4 mm
=
1.141732283 in
Wiki User
∙ 12y ago29.5 inches is equivalent to 749 millimetres
Wiki User
∙ 11y ago29mm is 1.14173 inches.
Direct Conversion Formula
29
mm
*
1 in
25.4 mm
=
1.141732283
in
Wiki User
∙ 15y ago29 inches are 736.6 millimeters.
Wiki User
∙ 8y ago29 millimeters is 1.14 inches.
Add your answer:
Earn +20 pts
How many feet and inches in 568 inches?
47 feet 4 inches.
6.89 inches is how many in inches?
6.89 inches.
How tall is 5.5 feet in inches?
5 feet 5 inches=65 inches total (there are 12 inches in one foot)
From 22 inches to 16 inches?
22 inches to 16 inches is a decrease of six inches.
How many inches is 5 feet 4 inches?
Your 5 feet 4 inches is 64 inches. There are 12 inches per foot which, when multiplied by 5 (the number of feet) will give you 60 inches. Add the 4 inches and the sum is 64 inches.There are 12 inches in a foot. It would be 64 inches.
Homany inches is 29mm?
It is about 1 inch
How many inches does 29mm equal?
1.14 inchesDirect Conversion Formula29mm*1 in25.4 mm=1.141732283in
What is 2.9cm into millimetres?
It is: 2.9cm = 29mm
How many 29mm are the in meters?
29 millimeters is 0.029 meters.
What size is axle nut on a 1996 Pontiac sunfire?
this should be easy to find but it isn't don't know why ! people that right on forums are to stupid to include ........ " remove the axle nut" correction = remove the axle nut using a 29mm socket! how hard was that !!!!!!! 29mm is what you need for that nut !
What size socket do you need to undo the rear hub nut on a ford focus?
Mk1 Focus 29mm 235Nm
How large is St Jude Mechanical Aortic Valve?
The are available in multiple sizes depending on size of patient. My aortic valve is 29mm.
What is Rear hub nut torque setting on a 1.8 ford focus?
Mk1 Focus Euro spec (not US), rear hub nut, the big one in the middle, 29mm socket, torque to 235Nm
How talla re the warhammer models?
It depends on whether it is the epic (around 5mm), warmaster (around 2mm), warhammer fantasy (around 29-30mm) or warhammer 40,000 (28-29mm). It also depends if you mean the troops, or the vehicles and monsters.
What is the socket size of the front axle nuts on a 2004 KIA Rio?
The socket size for the front axle nut on a 2004 KIA Rio is typically 32mm. It is recommended to verify this size with the specific vehicle to ensure a proper fit.
What is a dead zone in sensors?
A dead zone in a sensor is the point where a sensor will not work. Ultrasonc sensors and specific optical sensors for example have measurement or detection ranges quoted as 30mm-300mm sensing. This means the sensor will not operate from 1-29mm or over 300mm.
What size socket is needed to remove a hub nut on a n reg ford escort?
29mm on mine at the rear, had to order socket off the net cause it seems to be an unpopular size in shops. might need a breaker bar too, as its extremely tight!
