answersLogoWhite

0

You must read from the bottom of the meniscus. In a narrow, graduated glass cylinder, water has a slightly domed surface, with the centre being higher than the side, so giving a false reading if the centre height is taken.

User Avatar

Wiki User

7y ago

What else can I help you with?

Continue Learning about General Science

What is a graduated cylinder used for in science?

A graduated cylinder is a piece of laboratory glassware used to accurately measure out volumes of chemicals for use in reactions. They are generally more accurate and precise for this purpose than beakers or erlenmeyer flasks, although not as precise as a volumetric flask or volumetric pipet. They come in a variety of sizes for different volumes, typically 10 mL, 25 mL, 50 mL, or 100 mL and up to as large as 1 or 2 liters.Determine the volume contained in a graduated cylinder by reading the bottom of the meniscus at eye level.In other words, holding the graduated cylinder at eye level, the bottom of the curved surface of the liquid (called the meniscus) is where you read off the mark on the graduated cylinder to determine the volume properly.


What is the bottom of the curve of liquid in a graduated cylinder?

Since the surface of water rises up to the sides of the cylinder, the low point is in the center of the surface. (Volume is assumed unless boiling or melting points are stated)


When measuring a small quantity of liquid which instrument would permit the most accurate reading?

If available, a small, glass graduated cylinder would be best. Next best would be a test tube or any clear or semi-transparent cylinder/ small plastic recycled container/bottle. If an eyedropper is not available, recycle a milkshake straw to move/transfer small quantities of a liquid. Place the bottom end of the straw in the liquid almost to the bottom. Then hold your thumb tightly to the top end of the straw and lift out of the liquid. When you remove your thumb the contents will spill out of the bottom of the straw.


What should you look at to measure a volume of water in a graduated cylinder?

Place the cylinder on a flat surface. Read the volume contained in a graduated cylinder or volumetric flask, by comparing the bottom of the meniscus (the curved surface of the liquid),at eye level, to the nearest graduation or ring.


How do you measure 250ml liquid?

a metric measuring cup

Related Questions

When reading a graduated cylinder you look at?

When you read a scale on the side of a container with a meniscus, such as a graduated cylinder or volumetric flask, it's important that the measurement accounts for the ... For mercury, take the measurement from the top of the meniscus. ...


Reading the volume of liquid inside the graduated cylinder?

Always read from the bottom of the meniscus (where the liquid reaches up the side of the container).


Can you explain how to read the meniscus in a graduated cylinder when measuring the volume of a liquid?

To read the meniscus in a graduated cylinder when measuring liquid volume, look at the bottom of the curve where the liquid meets the cylinder. Read the measurement at eye level to get an accurate volume reading.


Where is the least dense liquid found in a graduated cylinder?

The least dense liquid is found at the bottom of the graduated cylinder, because the less dense it is, the farther it will go down in th graduated cylinder.


Why you use graduated cylinder to measure 55 ml?

A graduated cylinder is used to precisely measure volumes of liquid. By pouring the liquid carefully into the graduated cylinder and reading the measurement at the bottom of the meniscus (liquid curve), you can accurately measure 55 ml of liquid.


What are the rules for reading a graduated cylinder?

When reading a graduated cylinder, make sure your eye level is even with the meniscus - the curved surface of the liquid. Read the measurement at the bottom of the meniscus to get an accurate reading. Take into account any calibration markings on the graduated cylinder to ensure proper measurement precision.


Point at the bottom of curve of a liquid in a graduated cylinder?

miniscus


What part of the miniscus is the volume of the liquid in the graduated cylinder measured at?

The lowest part. The highest part is hard to determine. At the bottom, ie the lowest point.


What is the the bottom of a curved line in a graduated cylinder?

The "bottom of a curved line" made by the liquid in a graduated cylinder could be called the "measuring line" or "reference line" in the application of that piece of labratory equipment. The curved surface of the liquid itself is called the meniscus, and we look to the bottom of the meniscus to make our reading as to the volume of the liquid in the graduated cylinder. The liquid in the cylinder "grabs" the sides of the cylinder and "pulls itself up" just a bit, and that creates the curve in the surface of the liquid. And that curve, the meniscus (which is from the Greek word for crescent), leaves us with a problem: where do we "read" the volume marked off by the graduations along the side of the cylinder? And the answer is, "At the bottom of the meniscus."


Why use a graduated cylinder for 100ml of liquid?

A graduated cylinder is used for measuring liquid volumes accurately. By using a graduated cylinder, you can precisely measure out 100ml of liquid ensuring the correct volume is dispensed. The markings on the cylinder allow for easy reading and accurate measurement.


When you are measuring the volume of water in a graduated cylinder do you look at the top of the meniscus or the bottom of the meniscus?

You should always measure the volume of liquid in a graduated cylinder at the bottom of the meniscus, where the curve of the liquid meets the cylinder's surface. This ensures an accurate reading of the volume contained in the cylinder.


How do you read a graduated cylindar with urine?

To read a graduated cylinder with urine, place the cylinder on a flat surface at eye level, ensuring the liquid is not spilling or forming bubbles. Read the measurement at the bottom of the meniscus, the curved surface of the liquid. Take note of the volume marking that aligns with the bottom of the meniscus for an accurate reading.