0
What else can I help you with?
What is typical line voltage tolerances?
Tolerances are about +/- 5 percent. Scroll down to related links and look at "List of countries with mains power_plugs, voltages and frequencies - Wikipedia".
Does voltage vs current graph passes through origin?
Yes. While it isn't clear what device you are talking about, and different devices have different characteristic curves (for example, a straight line for a resistor), a voltage is required for a current to flow, so if there is no voltage, there won't be any current, either.
Why Base Transceiver Station equipments require negative 48 volt DC to function properly why not positive?
it has two reasons.one is to prevent corosion due to the elecrtolitic effect and the other is to protect operator from the line voltage.. it has two reasons.one is to prevent corosion due to the elecrtolitic effect and the other is to protect operator from the line voltage..
What is a temperature line?
a temperature line is a line of temperature
What is a normal line in science?
A line is normal to another line when it is perpendicular.
What is the typical line voltage for gas furnaces?
The typical line voltage for gas furnaces is 120 volts for residential units and 240 volts for commercial units. This voltage powers the components such as the blower motor, ignition system, and controls in the furnace. It is important to ensure the voltage is compatible with the furnace to prevent damage or malfunction.
How the voltage regulation in 33kv line?
It does not depend on the line. The regulation is the percentage change in voltage caused by applying the full load current, and that depends on the transformer supplying the line. A value of 5% would be typical.
What is a condensate line in a furnace?
its the drain line for water to drain
What is edge speed in electronics?
A voltage is applied to a signal line. The voltage of the line changes gradually from 0 to +V. The "edge speed" is the rate of change of voltage of the line. A voltage is applied to a signal line. The voltage of the line changes gradually from 0 to +V. The "edge speed" is the rate of change of voltage of the line.
How do you convert 3 phase RMS line-line voltage to RMS line-neutral voltage on an unbalance system Basically how do you calculate using trig for all 3 phase?
The term, 'unbalanced system' refers to an unbalanced load. Under normal circumstances, an unbalanced load leads to unbalanced line currents. The line voltages are determined by the supply and remain symmetrical, even when the load is unbalanced. As your question refers to a 'line to neutral' voltage (i.e. a phase voltage), you must be referring to a star (wye) connected load, in which case the phase voltage (line to neutral voltage) is 0.577 (the reciprocal of the square-root of 3) times the line voltage (line to line voltage).
Is 220V line voltage or phase voltage?
Phase, if you are referring to line, as power line from pole.
What is the line voltage between two lines?
the voltage between 1 line & phase =120v The voltage between 2 line =240
Where should I drain the furnace condensate line?
The furnace condensate line should be drained into a suitable drain or outside through a designated drainage point to prevent water damage and ensure proper functioning of the furnace.
Why is phase voltage not twice line voltage?
Line to line voltage is not the same as line to neutral voltage because line voltages are 120 degrees apart. They are related by: Line to neutral voltage * tan (120 degrees) = Line to neutral voltage * 1.73.Additional CommentFor delta-connected systems, the line voltage is the same as the phase voltage.For wye-connected systems, the line voltage is larger than the phase voltage by a factor of 1.732. The reason for this is as follows:Because any two phase voltages are displaced from each other by 120o, they must be added vectorially, not algebraically, to find the line voltage. As the above answer points out, this means that the relationship between the two is the square-root of 3, or 1.732.
What is a line to line voltage?
In a 3 phase system, the voltage measured between any two phase is called line to line voltage.And the voltage measured between line to neutral is called phase to neutral (line to neutral) voltage.AnswerThere is no such thing as a 'phase-to-phase' or a 'phase-to-neutral' voltage. The correct terms are 'line-to-line' and 'line-to-neutral'.The voltage between any two line conductors is called a line voltage.In a three-phase, three-wire, system, the line voltage is numerically equal to the phase voltage.In a three-phase, four-wire, system, the voltage between any line conductor and the neutral conductor is called a phase voltage. The line voltage is 1.732 times larger than the phase voltage.
How do you hook propane gas line to gas furnace?
To hook a propane gas line to a gas furnace, you will need to connect the gas line to the furnace using approved fittings or connectors. It is important to ensure that the gas line is correctly sized for the furnace's gas requirements and that all connections are secure and leak-proof. It is advisable to hire a professional to install the gas line to avoid any safety hazards.
Is transmission voltage a phase to phase voltage or a phase to ground voltage?
Phase to Phase voltageCorrection to the above answer:There is no such thing as a 'phase-to-phase' or 'phase-to-ground' voltage. The correct terms are 'line-to-line' (or 'line voltage') and 'line-to-ground' (or 'phase voltage'). Transmission-line voltages are line-to-line (or 'line') voltages.
