answersLogoWhite

0

Earlier forms of lighting, such as gas lights, were expensive, dangerous and gave less light than the electric light. Gas lights could not be used in places with a fire or explosion hazard.

User Avatar

Wiki User

7y ago

What else can I help you with?

Related Questions

Is circuit part of a light bulb?

Yes, a circuit is a part of a light bulb. It is designed to provide the necessary electrical connection for the bulb to receive power and emit light. Without the circuit, a light bulb would not be able to function properly.


Is it necessary to remove the tail light assembly to change the tail light bulb on a Mazda MPV?

Yes unfortunatly


Why the circuit should close for the light bulb to light up?

The circuit needs to be closed for the light bulb to light up because it allows current to flow uninterrupted from the power source through the light bulb, which then converts electrical energy into light and heat. If the circuit is open, the flow of current is interrupted, and the light bulb will not receive the necessary electrical energy to produce light.


Who invented the electric light bulb what year was it invented and why was it necessary?

The first electric light was made by Humphry Davy in 1800. But it was not practical. A practical light bulb was developed by Thomas Edison in 1879. The light bulb revolutionized the world by making it possible to carry on near normal behavior at night. Prior to the light bulb people had only the dim light of candles and flame lamps.


How do you replace a brake light bulb in 97 Honda Accord?

Open the trunk.Either carefully pry off the rear light trim covers, or unfasten the retainers then remove the trim covers.If necessary, you can unplug the electrical connector from the bulb assembly.Remove the bulb socket from the light assembly by turning it counterclockwise 1/4 of a turn.To remove the bulb, carefully pull it straight out of the socket.Installation is the reverse of the removal procedure.To ensure that the replacement bulb functions properly, activate the applicable switch to illuminate the bulb which was just replaced. If the replacement light bulb does not illuminate, either it is faulty or there is a problem in the bulb circuit or switch. Correct as necessary.


What is best known for Thomas Edison?

Thomas Edison is best-known for the light bulb.


Why is the filament in light bulb coiled?

The coiled filament in a light bulb is designed to increase the surface area of the filament. This helps to maximize the amount of light produced while also allowing it to reach a high temperature quickly, which is necessary for creating light through incandescence.


Where is the Light bulb list for 2005 cobalt?

2005 Chevrolet Cobalt Light Bulb Replacement GuideHigh & Low Beam Headlamp Light Bulb Size:9007LLParking Light Bulb Size:3157LLFront Turn Signal Light Bulb Size:3157LLRear Turn Signal Light Bulb Size:3057LLTail Light Bulb Size:3057LLStop Light Bulb Size:3057LLHigh Mount Stop Light Bulb Size:912Fog/Driving Light Bulb Size:H11-55WLicense Plate Light Bulb Size:194Back Up Light Bulb Size:921Front Sidemarker Light Bulb Size:194Rear Sidemarker Light Bulb Size:194Map Light Bulb Size:2825LLDome Light Bulb Size:562Step/Courtesy Light Bulb Size:212-2


What type of light bulb is compatible with a blue refrigerator light bulb?

The type of light bulb that is compatible with a blue refrigerator light bulb is typically an LED bulb.


How does a battery make a light bulb work?

If you place an end of a wire on the negative or positive side, put the outer metal part of the light bulb's cap on the other, and place the other end of the wire on the light bulb's cap's inner metal part, it will turn on.TipBefore you try to do this, always check that the voltage of the battery is equal to, or a bit less than, the voltage of the light bulb!Otherwise the light bulb may only give out a very bright flash and could easily be destroyed.


What is the name of the light bulb?

A light bulb


How does the Mag-Lite flashlight work?

A Mag-Lite flashlight works by using an incandescent light bulb or LED bulb, which is powered by batteries stored within the flashlight. When the bulb is switched on, the batteries provide the necessary power to generate light. The light produced is then focused and projected through a reflector and lens to create a concentrated beam of light.