0
What else can I help you with?
Which command will show the administrative distance of routes?
The "show ip route" command in Cisco devices will display the administrative distance of routes along with other routing information.
What is the total distance from London to Salisbury?
According the AA Route Planner (GB Edition) the distance is 92.7 miles, this will take about 2 hours and 7 minutes to drive, assuming you take the direct route and there are no stops, accidents, breakdowns or other hold ups en route.
What is the distance between Harrogate and Buxton?
According the AA Route Planner (GB Edition) the distance is 80.8 miles, this will take about 1 hours and 42 minutes to drive, assuming you take the direct route to the centre of each location and there are no stops, accidents, breakdowns or other hold ups en route.
What is Distance from Newcastle Tyne And Wear to Portsmouth?
According the AA Route Planner (GB Edition) the distance is 340.2 miles, this will take about 6 hours and 2 minutes to drive, assuming you take the direct route to the centre of each location and there are no stops, accidents, breakdowns or other hold ups en route
What is the driving distance from Fresno to Oakland?
It depends on the route you take but the approximate driving distance (using major roadways) is 178 miles.
What is the default administrative distance for RIP?
120
What the administrative distance and metric for static route?
The administrative distance for a static route is typically 1, meaning it is very reliable and preferred over routes learned from dynamic routing protocols. The metric for a static route is typically one hop, meaning it has a fixed cost regardless of network conditions or traffic load.
Which command will show the administrative distance of routes?
The "show ip route" command in Cisco devices will display the administrative distance of routes along with other routing information.
Which two statements correctly describe the concepts of administrative distance and metric?
Administrative distance is a way to prioritize routing information from different routing protocols; a lower administrative distance is preferred. The metric, on the other hand, is a value that represents the cost of a particular route, aiding in selecting the best path to a destination.
Show ip route command?
Compared to RIP, EIGRP has a lower administrative distance.
Wich two statements correctly describe the concepts of administrative distance and metric?
Administrative distance refers to the trustworthiness of a particular route. Routes with the smallest metric to a destination indicate the best path.
Which routing protocol has the most trustworthy administrative distance by default?
generally static routing protocol has the most trustworthy administrative distance .i.e; 1 and in dynamic routing protocols EIGRP has the best AD.
How can you know how many computers are path your network?
The route via Path B is installed because the EIGRP route has the best metric to network 10.2.0.0/16. The route via Path A is installed because the static route has the best metric to network 10.2.0.0/16. The route via Path B is installed because the EIGRP route has the lowest administrative distance to network 10.2.0.0/16. The route via Path A is installed because the static route has the lowest administrative distance to network 10.2.0.0/16.
What is the default administrative value of rip?
120
What route is used by the computer's default gateway to send traffic to remote networks?
Default route
When should you use a default route?
When you have routing enabled then you need default route (also calleddefault network or Gateway of Last Resort). You do not need default routeif you don't use routing. For example if you just have one router in your network there is no need for default route. When you have more than one router in a network you need default route.Note: If you connect to WAN (Internet) you need default route. The default route allows connection with Internet. If you are not using WAN and have one router than there is not need for default route but in these days everyone connects to the Internet so most likely your router has default route. When using router to connect to the Internet using DHCP this happens automatically so there will no need to configure default route manually. If you need to manually set default route then use the commands IP default-network or IP route 0.0.0.0 0.0.0.0 .More info can be found at Cisco's site - see the related link below.
What is the command for a default route on a router?
ip default gateway
