answersLogoWhite

0

What else can I help you with?

Continue Learning about Geometry

What is the thickness of b class gi pipe?

What is the wall thickness of B class G.I pipe? what is the weight per meter of B class G.I pipe


What cross-section do you get when you give a vertical cut to a circular pipe?

The answer depends on the orientation of the pipe and the cut. Even if the cut is vertical, it can be along the axis (length) of the pipe, at right angles to it or at a slant. If the cut is along the axis, the cross section will be two rectangles where the length of the rectangle is the length of the pipe and the width is the thickness of the pipe. If the pipe has negligible thickness, this may be taken to be two parallel lines. If the cut is at right angles to the axis then the cross section will be an annulus which, when the thickness is negligible will become a circle. Finally, if the cut is skew, then you will get ellipses which will collapse to a single ellipse for negligible thickness.


How do you weld MS pipe to GI pipe?

Grind the surface of GI pipe lightly to remove the skin which is about 0.1 to 0.2 mm, than weld the MS pipe as per the wall thickness and use accordingly the welding rod at the required gauge / Dia of the welding rod. this works fine.


Area of pipe when thickness of wall inner radius of pipe and length of pipe is given?

For a pipe of uniform radius and thickness, I believe the total surface area would be the Outside surface + Inside surface+ 2 times the surface of the ends. The inside radius(rinner), pipe thickness (t), and pipe length (L) are given.So you only need to find the outside radius (Rout) and then all areas can be calculated.The outside radius should be Rout=rinner +t. And note the perimeter of a circle is 2*pi*Radius and area of an annular region (in this case the ends of the pipe) is A= pi*(Rout2 - rinner2)For the outer pipe surface: Aout=2*pi*(Rout)*LFor the inner pipe surface: Ainner=2*pi*(rinner)*LFor each pipe end: Aend= pi*(Rout2 - rinner2)So the total surface area of the pipe would be: Aout+ Ainner+2* AendOr: Atotal =2*pi*(Rout)*L+2*pi*(rinner)*L+ 2*pi*(Rout2-rinner2)= pi*[ 2*L*(Rout + rinner)]+(Rout2 - rinner2)= 2*pi*[ L*( rinner +t + rinner)]+(( rinner +t )2 - rinner2)]=2*pi*(t+L)(t+2*rinner)Hopefully that is correct and helps.


Why 14' and above pipe size onwards NB is equal to OD of pipe?

In pipe sizing, nominal bore (NB) is used to indicate the approximate internal diameter of a pipe, while the outside diameter (OD) is the actual measurement across the pipe's exterior. For pipes sized 14 inches and above, the NB is equivalent to the OD because these larger pipes are often constructed to a standard where the wall thickness is relatively uniform, making the internal and external measurements more closely aligned. This simplification helps in standardizing pipe sizes for ease of specification and installation in larger applications.

Related Questions

What is the thickness of the pipe?

the wall thickness of sch 40 - 500mm dia pipe is 15mm or 16mm.


What is schedule 20 pipe?

its the thickness of the pipe wall


What is the wall thickness of 500mm pipe?

the wall thickness of sch 40 - 500mm dia pipe is 15mm or 16mm.


Piging for grp pipe line?

what will be thickness of grp pipe


What is the Difference between b and c class MS pipe?

The main difference is the thickness of the pipe Compare to A Class pipe B Class pipe thickness is more.Like that Compare to B class pipe C Class pipe thickness is more.


What is the thickness of b class gi pipe?

What is the wall thickness of B class G.I pipe? what is the weight per meter of B class G.I pipe


What is the weight per meter of 40 mm dia ms pipe hallow pipe?

The weight of a hollow MS (mild steel) pipe depends on the thickness of the pipe wall. The weight can be calculated by using the formula: Weight = 0.02466 * Thickness * (Outer Diameter - Thickness) for a round hollow pipe.


What is the wall thickness of b class GI pipe?

What is the wall thickness of B class G.I pipe? what is the weight per meter of B class G.I pipe


What is the difference between schedule 40 and 10 gauge pipe?

The gauge of the pipe is the wall thickness. It is easier to say Schedule 40 pipe than .180 inch wall thickness. This is the SCH 40 wall thickness for a standard 12" pipe and the actual gauge thickness will vary based on pipe size and material. The larger the Schedule number, the thicker the pipe wall thickness. Pipe Schedule is also expressed in Std., X-Stg., and XX-Stg. since some thicknesses are more common than others.


What does pipe schedule means?

It refers to the strength and wall thickness of the pipe.


What is the weight of mild steel pipe OD 40mm and wall thickness 4mm?

=3.14 * (Diameter of pipe in Mtr. - wall thickness in Mtr. ) * Wall Thickness in Mtr. * 7850


How can you calculate the ID of a pipe?

Can you calculate the ID of a pipe when you have the OD to be 10.75" and the wall thickness to be 0.5"Depends on what you know about it. If you have the outer diameter and you know the wall thickness, then ID = OD-2 x wall thickness