0
What else can I help you with?
How many pieces of pipe can be cut from a 12 foot piece of pipe if each is to be one third of a foot long?
12/(1/3) = 36 pieces
What is a lineal foot?
A lineal foot is is one foot along the ground. A 12" ruler is a lineal foot.
If you are too big for one scale to read can you weigh with two putting one foot on one scale and the other foot on the other?
no you can not. There would be no way to tell how much weight was being read on both scales. You have to go out and buy a scale that has a higher weight allowance.
How many square cm is one square foot?
One square foot is 929.03 square centimeters.
How much in meters is 5x5 square feet?
Not easy to answer, since you are comparing a linear measure with a square or surface measure. But let me try to explain : One foot is 12 inches. One inch is 25.4 mm or 0.0254 meters One foot is 0.3048 meters 5 foot are 5 x 0.3048 m = 1.524 m 5 x 5 foot are 1.524m x 1.524m = 2.322576 m² or roughly 2.32 m²
How much 2 inch pipe will hold a gallon of water?
A two inch pipe can hold 0.1632 gallons per foot. It takes slightly over 6 feet of two inch pipe to hold one gallon of water.
How many gallons of water will a foot of 3 inch pipe hold?
One foot of 3 inch pipe will hold approximately 0.625 gallons of water.
How many gallons of water per foot will a one and one quarter inch pipe hold?
0.212 331 gallons per foot.
How much does a 3 inch diameter by one foot copper pipe weigh?
40
How much water will one foot of six inch pvc pipe hold?
The formula for this goes like this: radius of the pipe squared (32) x pi (3.1416) x length of pipe (12) = volume (amount of water). So 32 x 3.1416 x 12 = 339.2928 or about 339.3 cubic inches.
How much water is in a square of 1 foot?
A square foot cannot hold water its 2 dimensional. What you see is what you get . A one cubic foot container can hold 7.48 US gallons of liquid.
How many gallons of water will a 4 in PVC pipe hold per feet?
0.1631168The value 0.1631168 is the number of US gallons per foot of 2" pipe. The number of gallons per foot of 4" pipe is 0.652798
How many cubic inches of water are in a 1 inch pipe one foot long?
A 1-foot length of a pipe with an 1-inch internal diameter will hold pi*r2*h cubic inches where r = 0.5, h = 12 So 9.42 cubic inches.
How much is one cubic foot?
One cubic foot is a measure of volume. A one cubic meter container could hold up about 264 gallons of water.
How many pieces of pipe can be cut from a 12 foot piece of pipe if each is to be one third of a foot long?
12/(1/3) = 36 pieces
How much water will one cubic foot of air hold at eighty degrees?
2 cubic feet
How many gallons of water does a one foot 4 inch PVC pipe hold?
Assuming that the INNER DIAMETER of the PVC pipe is 4" (...likely not the case, so you'll need to recalculate for your pipe's dimensions): the volume of the pipe would be calculated as follows: 4" diameter = 2" radius volume_cylinder = Pi*r^2*L; where r = 2" and L = 12" the cylinder therefore has a capacity of 150.8 cubic inches. a gallon of water has the volume of 231 cubic inches. your pipe can hold 0.653 gallons of water. you'll need about 18.38 inch lengths of 4" PVC to hold each gallon of water. again, these calculations rely on the INNER DIAMETER of the pipe being measured at 4" - if this is an outer diameter measurement, the above calculation for the capacity is OVERstated; the 18.38" calculation is UNDERstated.
