0
What else can I help you with?
is there a way to tile over plywood on a bathroom floor?
You would be better of removing the plywood floor completely - and tiling over the original surface.
What is the r value of plywood?
¼-inch plywood 0.31 3/8 inch plywood 0.47 ½-inch plywood 0.62 5/8 inch plywood 0.78 This is taken from http://www.sizes.com/units/rvalue.htm, which also has some other materials that could/would commonly be used alongside with plywood to increase the R Value such as building paper and insulation... if both sides of the frame are ply then you must also include the void.
What has infinite length but width no thickness and no endpoints?
This would be a line, which has no width, no thickness and no endpoints, but has infinite length.
What two instruments would you use to measure the diameter and thickness of a material?
Micrometer and Vernier
How much does 300X300 inch marble weigh?
The weight of a 300x300 inch marble slab depends on its thickness and the density of the marble. Generally, marble weighs about 170 pounds per cubic foot. Assuming a standard thickness of 1 inch, a 300x300 inch slab would weigh approximately 1,875 pounds (or about 850 kg). If the thickness varies, the weight would need to be adjusted accordingly.
What are the differences between 5/8 and 3/4 plywood for subflooring, and which thickness would be more suitable for my project?
The main difference between 5/8 and 3/4 plywood for subflooring is the thickness. 3/4 plywood is thicker and therefore stronger than 5/8 plywood. The choice of thickness depends on the specific requirements of your project. If you need more strength and durability, 3/4 plywood would be more suitable.
What units would you measure the thickness of a glass pane?
Millimetres
What is the standard floor thickness?
I think you mean sub-floor. There are a few standards. 3/4 plywood or osb. 1 1/8 Plywood. 2 x 6 tounge and groove pine. Each has its advantages. I would consider the 1 1/8 T&G plywood to be the minimum standard.
What would be a good material for insulating electrical wire for safety purposes?
It really depends on what gauge (Thickness) of wire were talking about, but plastic and rubber are the most common ones.
Will 12 mm thickness glass will withstand the pressure of vacuum?
Glass with a thickness of 12 mm is generally capable of withstanding the pressure of a vacuum. However, it is important to ensure that the glass is of high quality and properly installed to avoid any potential issues or breakage. Consulting with a glass specialist or engineer would be advisable for a specific application.
Does electricity pass through camera lens?
Assuming the lens of the camera is made of glass, the answer is no. Glass is a very good insulator and it would an extremely large current (along the order of lightning) to overcome the insulating properties inherent in glass.
How would you carry out to find out how the thickness of a layer of insulating material affects the energy transfer through it?
You can conduct an experiment by using varying thicknesses of the insulating material and measuring the amount of energy that passes through each layer. Compare the results to determine how thickness impacts energy transfer. Ensure that other variables, such as the material type and temperature, remain constant for accurate conclusions.
How many cubic metres in a sheet of ft by ft sheet of plywood?
To calculate the volume in cubic meters of a sheet of plywood that measures feet by feet, you first need to convert the dimensions from feet to meters. There are approximately 0.3048 meters in a foot. Once you have the dimensions in meters, multiply the length by the width and the thickness (if known) to get the volume in cubic meters. For a standard 4 ft by 8 ft sheet of plywood with a typical thickness of 0.019 m, the volume would be approximately 0.1 cubic meters.
How many pieces of thin light glass will have the same effect of one thick dark glass?
It would take several thin light glass pieces stacked together to achieve the same effect as one thick dark glass. The number would depend on the specific properties of the glass, such as thickness and light transmittance.
What unit would you use to measure the thickness of a cup Why?
Thickness is measured in units of length. You'd have to choose the one that gives a reasonable number corresponding to whatever you're measuring the thickness of. If it's the thickness of a hair, you'd probably select a sub-multiple of a meter. If it's the thickness of the atmosphere, you might select the kilometer. If it's the thickness of country gravy, that's a whole different story.
What is the unit measurement of plywood?
The answer depends on what characteristic you wish to measure: its length, width, thickness, density, rigidity, etc.The answer depends on what characteristic you wish to measure: its length, width, thickness, density, rigidity, etc.The answer depends on what characteristic you wish to measure: its length, width, thickness, density, rigidity, etc.The answer depends on what characteristic you wish to measure: its length, width, thickness, density, rigidity, etc.
How much pressure does it take to punch through a sheet of plywood in one square inch?
The amount of pressure needed to punch through a sheet of plywood in one square inch depends on the thickness and type of plywood. In general, it would require a significant amount of force given the strength and density of plywood materials. Commercial hydraulic presses could exert enough pressure to achieve this, generally ranging from 3000-5000 pounds of force per square inch.
