0
What else can I help you with?
What electronic component stores instructions waiting to be executed?
No single type of component does this, it is done by a circuit composed of many different components.
List of vietnam war veterans in US?
A list of deceased Vietnam War veterans in the US can be found on the Vietnam Veteran's memorial. You can also find this type of list by contacting the VA in your area.
When did Nikola Tesla create the Tesla coil transformer?
In 1891, Tesla invented the Tesla coil, which was widely used in radios and television sets. A Tesla coil is a type of resonant transformer circuit.
What is a relay instrument?
Relay is an electrically driven switch. It is an electromagnet to perform switching mechanically but other type of switches are also available. It is employed when a circuit is required to be controlled with a low input signal.
What is an xlr cable?
XLR refers, not to the cable (wire) per se, but actually to the type of connector used. An XLR connector has 3-pins and is used primarily in audio. Professional microphones and other audio equipment use it. Of the three pins, two are for the balanced signal, and one is for the shield. The wire used then is a two conductor shielded cable using a braided wire or a foil shield. So, an "XLR cable" refers to a two conductor, shielded cable with XLR connectors on each end.
What is the type of circuit called when it has an conductor a switch a electric cell a resistor?
The type of circuit you are describing is known as a simple circuit. It consists of a power source (electric cell), a switch, a conductor (usually wire), and a resistor to control the flow of electric current.
What type of electrical trouble occurs when a hot conductor comes in contact with a neutral conductor and bypasses the load device?
shorted circuits
In what type of circuit does the vehicles frame or body serve as an electrical conductor?
In a(n) , the vehicle's frame or body serves as an electrical conductor
What 's the type of unwanted current flowing in a neutral conductor?
A leakage current to ground indicates that the ground is not truly an earth ground. A Ground Fault Circuit Interrupter (GFCI) is designed to detect such leakage current and cut off the device from its supply voltage.
Where is the neutral switch circuit on x type?
it's located under the battery well. i hope this helps.
What is the role of a neutral wire?
The real purpose of neutral is grounding. In order for electricity to flow you need a direct continuous link from the supply to a ground. Without the neutral electricity wouldn't be able to flow because it wouldn't have a ground (a place to go). The real name for neutral is the grounded conductor, and what is commonly referred to as ground is really the grounding conductor. The grounding conductor exists for the sole purpose of being a back up neutral in case something happens, this way you don't BECOME the ground if you touch it. But don't think that means you can go touching wires if you don't know what your doing cause you can still get hurt even with both grounded and grounding hooked up.
What is TPN MCCB?
A TPN MCCB is a three phase neutral molded case circuit breaker. This type of circuit breaker is commonly used in low voltage power distribution systems.
How are the live neutral and ground wires connected to a duplex grounding type receptacle?
The black "hot" conductor goes to the brass coloured screw. The white coloured conductor goes to the silver coloured screw. The bare ground conductor goes to the ground green coloured screw
What type of energy flows in a circuit?
Electrical energy flows in a circuit, which is the movement of electrons through a conductor like a wire. This flow of electrons creates an electric current that powers devices connected in the circuit.
What is ribbed neutral wire?
In a two wire zip cord, often used to simple appliances such as table lights, the ribbed conductor should be connected as the neutral conductor. The ribbing is there to help you find the neutral. On the plug end, neutral is the wide prong. On the lamp end, neutral is the outside of the socket. (Hot is switched and connected to the center pin.) The reason for this is that when you change a light bulb by feel, if you touch the screw part of the base while it is still partially screwed in, you do not want to come into contact with hot, in case you are also touching something else, such as ground.
Is a copper conductor or a insulators?
Copper is a conductor of electricity.
What type of connection will cause an overload current?
A connection between the "hot" and the neutral will cause an over current condition. In electrical terminology this is known as a short circuit.
