0
To remove the lock nut on the sprocket of a Yamaha YZ125, first ensure the bike is secure and the rear wheel is off the ground. Use a suitable wrench to hold the sprocket in place while you turn the lock nut counterclockwise. If it's difficult to loosen, you may need to apply some penetrating oil and allow it to sit for a few minutes. Once loose, remove the lock nut and the sprocket can be taken off.
What else can I help you with?
What size is the primary sprocket nut on a 2001 sportster?
The primary sprocket nut is 1 - 1/8 inch.
Where does a lock nut go?
A lock nut should go on a bolt before a washer or the nut.
Where is the stator on a 99' Harley Dnya FXD?
It is behind the sprocket shaft nut.
How do you change the front sprocket raptor 660?
straighten the bent washer, Did you buy spare lock washers? remove the nut, 1-1/4" or 32 mm, I stand on the rear brake loosen the chain adjustment work the front sprocket out if the chain, it's tougher with a 14 tooth install new sprocket Don't forget to bend the washer back over the nut if you have the stock chain it might not have a master link so i cut mine but there is a way to take it off without cutting .
What size is front sprocket nut 600 bandit?
The front sprocket nut on a Suzuki Bandit 600 typically requires a 27mm socket for removal. It's important to ensure that the nut is torqued to the manufacturer's specifications when reinstalling. Always refer to the motorcycle's service manual for specific details and guidelines.
What is the tourque for a 1989 Harley Sportster crank sprocket nut?
160 foot pounds
Is the nut that holds the front primary sprocket on right or left handed thread?
The front compression nut is right handed, however the nut hold the clutch hub is left handed.
Torque spec on a 1995 yz 250 countershaft sprocket nut?
25 ft lb
How do you install a front sprocket on a Honda dirt bike?
Press down the rear foot brake and use a breaker bar or large ratchet with correct size socket to loosen nut on front sprocket. (never use impact wrench NEVER EVER!)Once you get the nut broken loose. Unclip your chain and put the gear in neutral and pull the chain through and set it aside. Put clutch in first gear and continue to ratchet loose the nut. Loosen nut all the way. Change out the sprocket. Tighten nut as much as you can with bike in gear. Put your bike back in neutral and feed your chain around the sprocket pulling it through and resting both sides of it on the rear sprocket where you will reclip the master link. Meeting both sides of the chain on the rear sprocket will make it easy to clip as the rear sprocket holds your chain for you. Once master link in chain is clipped. Step on the rear brake and crank down to spec lbs on the front sprocket bolt. If you don't know the foot lbs.. just make sure its real tight. Your done!
How to change front sprocket on gsxr750?
To change the front sprocket on a GSX-R750, first, ensure the bike is on a stable stand and remove the chain guard for access. Loosen the rear axle nut and the chain adjuster bolts to relieve tension on the chain, then remove the chain from the sprocket. Use a socket to remove the front sprocket retaining nut, replace the sprocket, and reassemble in reverse order, ensuring proper torque settings. Finally, adjust the chain tension and check for smooth operation before riding.
How do you change the chain drive sprocket on a stihl 051AV. There is not a chain break so the sprocket spins with the retaining nut.?
you have to prevent the crankshaft from turning when you loosen the retaining nut. the nut is probably left-hand threads(loosen by turning clockwise). remove the spark plug, turn the sprocket (and crankshaft) to the left until the piston is at the bottom of the cylinder, insert enough nylon pull starter rope into the spark plug hole to fill the cylinder, turn the sprocket to the right until the rope is compacted enough to prevent the piston from moving, put a wrench on the nut and tap with enough force to break it loose. replace the sprocket and use the same process in reverse to tighten the nut, don't go nuts tightening, it will tighten itself as you use the saw. a dealer might give you the correct torque specs.
What is the correct order for installing a lock washer?
The correct order for installing a lock washer is to place it between the nut and the surface being fastened, with the teeth of the lock washer facing towards the nut.
