0
There's no way of telling, as chain length is decided by frame size (=chain stay length) + driver + sprocket tooth count. Chains are always sold a few links too long, and are then cut to size when they're installed on the bike. If you're doing this yourself, get a chainbreaker tool. For what they cost, they can sure save you a lot of swearing.
What else can I help you with?
What size half chain link do you need if i get a 25t sprocket?
The chain length needed is determined by chainring size, sprocket size and the design of your frame. There's no way of saying that you'll need from the sprocket alone. On top of that there isn't much to choose from when it comes to half links. They are all of the same length and in width there are two options 1/8" or 3/32". You need one the same width of your chain.
What size half chain link do you need if you get a 36t sprocket?
Half links only come in two sizes, 1/8" and 3/32". Which one you need is determined by which chain you're running. Depending on which sprocket you had before a half link may not be enough. On a bmx just make it fit, they tend to slack by half an inch to adjust while peddling back since they don not lock. Meassure until nearest like possible.
What is the process for bike sprocket replacement?
To replace a bike sprocket, you will need to first remove the chain from the sprocket. Then, use a wrench to loosen the bolts holding the sprocket in place. Once the bolts are removed, take off the old sprocket and replace it with the new one. Secure the new sprocket in place by tightening the bolts. Finally, reattach the chain to the new sprocket.
What kind of sprocket do you want for a small bicycle chain?
well if you have a 8 tooth rear driver you will need a 23t sprocket, if u have a 9 tooth rear driver you will need a 25t sprocket, if u have a 10 tooth rear driver you will need a 28t sprocket, and if you have a 11 tooth rear driver you will need a 30t sprocket
What chain do you need for a 28t sprocket and a 10t driver?
You need a chain meant for single-speed or internally geared bikes, cut to the right length.
What do you do For the timing chain where do the timing marks need to be located on top of bottom sprocket and on top or bottom of top sprocket?
the marks have to be pointing each other in the center of the gears
How can I remove the rear sprocket from a bicycle wheel?
To remove the rear sprocket from a bicycle wheel, you will need a chain whip tool and a cassette lockring tool. First, remove the wheel from the bike. Then, use the chain whip tool to hold the sprocket in place while using the cassette lockring tool to unscrew the lockring that holds the sprocket in place. Once the lockring is removed, the sprocket can be taken off the wheel.
How can I remove a bicycle sprocket?
To remove a bicycle sprocket, you will need to use a chain whip tool and a cassette lockring tool. First, remove the wheel from the bike. Then, use the chain whip tool to hold the sprocket in place while using the lockring tool to loosen and remove the lockring. Once the lockring is removed, the sprocket can be taken off the wheel.
How can I remove a bike sprocket?
To remove a bike sprocket, you will need to use a chain whip tool and a cassette lockring tool. First, remove the wheel from the bike. Then, use the chain whip tool to hold the sprocket in place while using the lockring tool to loosen and remove the lockring. Once the lockring is removed, the sprocket should slide off easily.
What is the process for replacing a sprocket on a bicycle?
To replace a sprocket on a bicycle, you will need to first remove the old sprocket by loosening the bolts or screws that hold it in place. Then, you can install the new sprocket by aligning it with the chain and securing it with the bolts or screws. Finally, make sure the sprocket is properly tightened and test the bike to ensure it is functioning correctly.
Where in the timing chain in a Toyota Previa 92?
right in front of the crankshaft pulley beside the oil filter....is the timing chain cover(two timing chain...#1 on the crankshaft sprocket, #2 on the cam sprocket. Need to lower the engine to access the timing chain. Timing chain, not necessary to be replace, unless they broke loose.Other than that it remain with the life of the van.
The rear socket on my mens Schwinn high timber bike keeps turning when I stop pedaling causing the chain to fall off what is wrong with my bike?
The bent sprocket is guiding the chain diagonally causing it to be unparalleled with the front sprocket, you will either need to purchase a new rear sprocket or find a way to bend the rear one back straight
