0
What else can I help you with?
How do you call someone who uses the products made by industry?
If your question is "What do you call someone who uses the products made by industry?", you call him a consumer.
Does Exxon Mobil uses JIT?
All the oil companies uses JIT, which causes spikes in prices when demand is too high.
What is agricultural industries?
Industrialized Agriculture uses heavy equipment and large amounts of financial capital. It also uses pesticides to produce single crops or monoculture.
What are some iron ore uses?
iron and steel
Who uses G clamps in their profession?
A professional that uses a drill or driver for most of their day would also use G clamps. This can be any professional builder, landscaper, or general contractor.
What has the author Jan Verniers written?
Jan Verniers has written: 'Inleiding tot het militair strafrecht en strafprocesrecht' -- subject(s): Courts-martial and courts of inquiry, Military offenses
How do you set and adjust tools ( such as squares protractors and verniers in fitting?
To set and adjust tools like squares, protractors, and verniers in fitting, first ensure they are clean and free from debris. Use a calibration reference, such as a known straight edge or angle, to check the accuracy of the square or protractor. For verniers, zero the scale by aligning the jaws properly and adjusting the screw if necessary. Regularly verify tool settings during the fitting process to maintain precision in measurements.
How are squares protractors and verniers set and adjusted?
Squares, protractors, and verniers are set and adjusted by ensuring their measuring edges or scales are aligned accurately with the reference lines or surfaces. For squares, the blade is typically checked against a straight edge to confirm a right angle. Protractors are adjusted by aligning the zero degree mark with the baseline and ensuring the measurement arm is accurate. Verniers are calibrated by aligning the zero of the vernier scale with the main scale, ensuring precision in measurements.
What is the lease count of the venier calliper?
Verniers usually measure hundredths of a millimetre or thousandth of an inch depending on make and model.
What actors and actresses appeared in Framing and Unframing - 2001?
The cast of Framing and Unframing - 2001 includes: Jack Moylett as The Pedagogue Yuri Verniers as The Traveller
Why does a spectrometer have two verniers?
A spectrometer typically has two verniers to enhance measurement precision and accuracy when determining the wavelengths of light. One vernier is used for coarse adjustments, allowing the user to quickly approximate the wavelength, while the second vernier provides fine adjustments for more exact readings. This dual-vernier system helps minimize errors and facilitates more reliable spectral analysis.
Why is a micrometer better than a vernier caliper?
They are not. You use the most suitable instrument for the task in hand. Some people find verniers more difficult to read unless there is a digital readout.
What actors and actresses appeared in De lamp - 1971?
The cast of De lamp - 1971 includes: Raymond Bossaerts as Jan Paul Ricour as Arbeider Alice Toen as Katrien Greta Verniers as Buurvrouw
Tools in physics?
Rulers (meter rules etc..) Scales Balances (spring balances, lever balances etc..) Micrometers (Digital/Analogue) Verniers (Vernier Callipers) Timers (stopwatches, timing oscillations, electronic timers)
When was the vernier caliper invented?
It is the measuring instrument it is invented by verniers its error is very small
How would be the reading differ if the screw gauge is used instead of vernier calliper to measure the thickness of glass plate?
Verniers give you a less accurate approximation of the thickness, whereas a micrometer can give a more accurate measurement, often by 100 orders more accurate.
What are the tools in obtaining measurements?
30 cm ruler, 5 Metre steel roll up tape, Electronic scales , Spring balance scales, Scientific Beam Balance, Clocks, Watches, Sundials, The basic things which we measure are :- LENGTH, MASS, and TIME. All other measures are based on these three Also, Verniers, and Micrometers, and Weighbridges..
