To add a ground wire to an old house, you can hire a licensed electrician to install a new ground wire that connects to the electrical panel and grounding rods. This will help protect your home from electrical hazards and ensure safety.
Old house wiring that lacks a ground wire can pose potential hazards such as electrical shocks, fires, and damage to electronic devices due to the lack of proper grounding protection.
To add ground wires to old outlets, you can hire a licensed electrician to install a ground wire or use a ground fault circuit interrupter (GFCI) outlet as an alternative method. It is important to ensure that the wiring is done safely and in compliance with electrical codes to prevent electrical hazards.
To ground an outlet in an old house, you can hire a licensed electrician to install a grounding wire that connects the outlet to a grounding rod or the electrical panel. This will help protect against electrical shocks and ensure the outlet is safe to use.
Look in the back of the range receptacle box that is in the wall. The three wires coming in should have a bare ground wire in the cable set. It wasn't brought to the receptacle because there was no place for it on the three wire receptacle If you find it back there under a screw terminal just add another short piece of wire under the screw and then connect the other end of the short wire to the new ground terminal on the new four position receptacle The wire should be equal in size to the size of the wire that exists around the ground terminal now. If the house is so old that the range cable did not have a ground wire in it the code allows a separate green ground #10 wire to be taken from the breaker panel box to the existing range receptacle This wire is to be bonded on each end. At the panel end to the ground buss and at the receptacle end around the ground screw at the back of the box unbroken and then to the new four position receptacle ground lug.
The bare wire from the old 3-wire stove should be connected to the grounding terminal in the panel. The neutral and ground should not be bonded together at the stove. If the stove requires a 4-wire connection, it's best to run a new 4-wire circuit to meet current electrical codes for safety.
You need a 3 conductor wire with ground. For example if you had a 30 amp breaker for that outlet you would need 10awg 3w/ground. That's 10 gauge 3 conductor with ground and replace the old wire back to the panel.
There is a good chance that the green wire is your grounding wire. http://www.youtube.com/watch?v=KNo78fMZfRI&feature=PlayList&p=05D94AD4BF05DD32&index=5&playnext=4&playnext_from=PL Attach black to black with connectors and ground (green) to ground (usually a white wire in the box).
she is 6 years old, the youngest in the house.
No, never use the neutral conductor for anything but a neutral. If the house has no grounding system then there is no need to connect the fan ground wire to anything. Just keep in mind that the wiring in the house could be 70 plus years old and the insulation on this wire will be starting to break down if handled too much. Just cap the wire off and install the fan. Old two wire knob and tube systems were used in the 20's and they never used a ground with them. In the 40's NMD cable was used but it also never had a ground wire. It was in the early 60's that the third wire was added to NMD cable, it was a bare copper wire that was used for grounding equipment. Now the new wiring code states that there must be a grounding system in place for new installations.
The ground wire must remain connected to the box. The frame of the switch, and therefore also the screws, must remain connected to the box as well.
Actually they have 3. A round ground, wide neutral, and narrow hot. If it only has 2 it is an old outlet with no ground wire. If that is the case in your home, I highly suggest you connect a jumper wire from the ground screw to the white neutral wire on the silver screw to provide some protection. Do this at every outlet in the home. Replace all the outlets in your home with new ones if they are so old they do not have a ground connection.
Shut the power off to the recepticle. Then take apart the old outlet. Wire up the new outlet. The only difference between the old and the new will be the grounding. If BX armour cable is used, then you will need to take a jumper wire from the grounding nut on the outlet and connect it to the box with a grounding screw. This wire must be green. If romex has been used, then there is a gounding wire that is in the bundle of the wires coming into the box. If it a metal box, then you must use a grounding screw and ground that wire to the boc and then connect that same wire to the outlet. If its a plastic box, then just wire the ground to the outlet. I also like to wrap the outlet in electrical tape, just incase the the wires were to come loose, they would note hit against the box shorting out. Finally, put the pieces back together. And your DONE!