answersLogoWhite

0

To relight the water heater pilot, locate the pilot light button or knob on the water heater. Turn it to the "pilot" setting and hold it down. While holding the button down, use a long lighter to ignite the pilot light. Keep holding the button for about a minute after the pilot light is lit to ensure it stays on. If the pilot light continues to go out, there may be an issue with the thermocouple that needs to be addressed by a professional.

User Avatar

AnswerBot

4mo ago

What else can I help you with?

Related Questions

How can I check the water heater pilot light?

To check the water heater pilot light, locate the access panel on the water heater and look for a small flame. If the flame is out, follow the manufacturer's instructions to relight it safely.


How can I determine if the water heater pilot light is out?

To determine if the water heater pilot light is out, locate the pilot light access panel on the water heater. Look inside to see if the pilot light is lit. If it is not lit, you may need to relight it following the manufacturer's instructions.


Why did my water heater pilot light go out?

The pilot light on your water heater may have gone out due to a variety of reasons, such as a faulty thermocouple, a clogged pilot orifice, a gas supply issue, or a draft in the area where the water heater is located. It is important to troubleshoot and address the specific cause to safely relight the pilot light.


What should I do if the pilot light is out on my hot water heater?

If the pilot light on your hot water heater is out, you should follow the manufacturer's instructions to relight it. This typically involves turning off the gas supply, waiting for any gas to dissipate, and then using a long lighter to relight the pilot. If you are unsure or uncomfortable doing this, it is best to contact a professional plumber or the manufacturer for assistance.


What are the steps to relight the pilot on a hot water heater?

To relight the pilot on a hot water heater, follow these steps: Locate the pilot light assembly on the water heater. Turn the gas control knob to the "off" position and wait for at least 5 minutes. Turn the gas control knob to the "pilot" position. Press and hold down the pilot button while using a long lighter to ignite the pilot light. Continue holding down the pilot button for about 30 seconds after the pilot light is lit. Release the pilot button and turn the gas control knob to the desired temperature setting. Remember to refer to the manufacturer's instructions for specific guidance on relighting the pilot on your particular water heater.


How do I start a gas water heater?

To start a gas water heater, first make sure the gas supply is turned on. Then, locate the pilot light and follow the manufacturer's instructions to relight it. Once the pilot light is lit, adjust the temperature setting on the water heater to your desired level. Allow the water heater to heat up the water before using it.


How do I check the pilot light on my water heater?

To check the pilot light on your water heater, locate the access panel near the bottom of the unit. Open the panel and look for a small flame burning inside. If the flame is out, follow the manufacturer's instructions to relight it safely.


Why won't the pilot light on my water heater that got wet?

When a pilot light on a water heater gets wet, it may not light because the water can disrupt the flow of gas or cause electrical issues, preventing the ignition process. It is important to ensure the area is dry and free of moisture before attempting to relight the pilot light.


How can I safely relight the hot water heater pilot light in my home?

To safely relight the hot water heater pilot light in your home, follow these steps: Turn off the gas supply to the water heater. Wait for the gas to dissipate for at least 5 minutes. Locate the pilot light assembly and follow the manufacturer's instructions for relighting. Use a long lighter or match to ignite the pilot light. Once the pilot light is lit, turn the gas supply back on. Check for any gas leaks by using a soapy water solution on the connections. If you smell gas or encounter any issues, contact a professional for assistance.


How do you relight a natural gas pilot light?

How do you relight a natural gas pilot light?


How can I troubleshoot a water heater that is not working properly, specifically focusing on the pilot light and ensuring it is lit to provide hot water?

To troubleshoot a water heater that is not working properly, check the pilot light. Make sure it is lit to provide hot water. If the pilot light is out, follow the manufacturer's instructions to relight it. If it continues to go out, there may be an issue with the thermocouple or gas supply that requires professional repair.


How do I relight a heater's pilot light?

Usually you can relight it with a lighter, and it will be good. If not you should shut it off so that you don't have a fuel leak. It shouldn't take much to fix any way.