0
What else can I help you with?
Can 10-2 yellow wire be used to run low voltage lights?
10-2 wire can be used to provide power to low-voltage lignts.
What is difference between 10-2 and 10-3 wire?
The main difference between 10-2 and 10-3 wire is the number of conductors they have. 10-2 wire has two conductors, typically used for a hot wire and a neutral wire. 10-3 wire has three conductors, typically used for a hot wire, a neutral wire, and a ground wire.
How far can you run 102 wire without voltage drop?
I assume you mean 10/2, as in 10 awg, 2 conductor copperwire? The answer is zero feet. Any time you run a current through a wire, there is voltage drop, no matter how short the wire is. The longer the wire, the larger the voltage drop will be. What you really want to know, I think, is how far you can run 10 awg wire and stay within the acceptable limit of voltage drop. In the US, the National Electrical Code recommends no more than 3% voltage drop for a branch circuit. In this case the maximum run of 10 awg wire (assuming a 30 amp breaker and a 120 V circuit) would be about 48 feet. If the maximum load is less than 30A, then the run could be longer. For instance, if the max load were 15 A, the max run would double, to about 96 feet. If the supply voltage is 240 V instead of 120, then the run length is double the above figures.
How far will you travel if you run for 10 minutes at 2 mph?
At 2 mph it will take you 60 mins to run 1 mile. Therefore after 10 mins running you will have covered (10/60) *2 = 0.33 of a mile.
How many watts can run through 10-2 wire?
The 10-2 wire is typically rated for a maximum of 30 amps. To calculate the wattage that can run through this wire, you can use the formula: Watts = Volts × Amps. For a standard 120-volt circuit, this equates to 3,600 watts (120V × 30A). In a 240-volt circuit, it would be 7,200 watts (240V × 30A).
how far can you run 10 wire for 1500 watt 20 amps?
That is a voltage of 75 v. The distance is calculated by allowing a 5% voltage drop in the resistance of the wire, or 3.75 v. With 20 amps and a voltage drop of 3.75 volts the allowed wire resistance is 0.1875 ohms. 10-AWG wire has a resistance of 1 ohm per 1000 ft, so the total length of wire allowed is 188 ft. Assuming 2 wires the allowable distance is 94 ft.
What type of wire should be used for an air conditioner installation: 10/2 or 10/3 wire?
For an air conditioner installation, 10/2 wire should be used.
What is the amp rating for 10-2 wire?
The amp rating for 10-2 wire is typically around 30 amps.
What is the amp rating for 10/2 wire?
The amp rating for 10/2 wire is typically around 30 amps.
How far will you travel if you run for 10 minutes at 2msec?
If you run for 10 minutes at a speed of 2 m/s, you will travel a total distance of 1200 meters. Distance = speed x time.
Can 14-2 wire on a patio post be covered with white conduit?
Yes, that is fine as long as the wire does not run underground. If it does run underground you need 14-2U wire.
You want to wire up a receptacle to run a 2 hp 230 volt dust collector you have some NMD 90 14-2 available The run is about 50 feet from the panel Is this wire suitable and adequate?
No, NMD 90 14-2 wire is not suitable for a 2 hp 230 volt dust collector. You would need to use a wire with a higher ampacity such as NMD 90 10-3 wire to handle the current required for a 2 hp motor. Ensure to consult with a qualified electrician for proper wire sizing and installation.
