To wire an outlet with 2 wires correctly, connect the black wire to the brass screw terminal and the white wire to the silver screw terminal. Make sure the bare copper wire is connected to the green screw terminal for grounding. Turn off the power before starting and follow all safety precautions.
To wire a GFCI outlet with only 2 wires, connect the black wire to the brass screw and the white wire to the silver screw on the GFCI outlet. Make sure to follow the manufacturer's instructions and turn off the power before starting the installation.
An outlet can be properly grounded with only 2 wires by using a Ground Fault Circuit Interrupter (GFCI) outlet. The GFCI outlet can provide ground fault protection even without a separate grounding wire.
Based on the description, it sounds like you should wire the stove outlet as a 3-prong outlet since the cable you have appears to have two hot wires and a ground wire (wire braid). Connect the two black wires to the hot terminals and the wire braid to the ground terminal on the stove outlet. Remember to ensure that the circuit is properly grounded for safety.
Yes, a 220 outlet typically has two hot wires, one neutral wire, and one ground wire. The two hot wires each carry 110 volts, which combine to provide 220 volts for larger appliances like dryers and ranges.
A two-phase outlet has two hot wires and one neutral wire. It typically has four prongs, with two vertical prongs for the hot wires and one horizontal prong for the neutral wire. This type of outlet is commonly used for high-power appliances like stoves and dryers.
the bare copper is always a ground
Simply run a wire from that outlet to that wall switch. Be sure you use the exact same wire size that you find in that outlet. It will be AWG 12/2 or 14/2. Do not mixes wire sizes. Connect the ground to green ground screw at outlet, and white wire to silver screw, and black wire to gold screw. At the light switch connect all white wires together under a wire nut and push them back into the box. Connect the ground wire to the green ground screw on the switch. Now connect the 2 black wires you have left, power in and power out, to the 2 screws on the switch. Does not matter which wires you connect to the 2 screws.
To replace a 2 prong outlet with a 3 prong outlet, you will need to turn off the power to the outlet, remove the old outlet, install a new 3 prong outlet, connect the wires correctly, and secure the outlet in place. It is important to follow safety precautions and consult a professional if needed.
If both the black and white wires are hot, it sounds like the wiring may have been done incorrectly. It's important to have a licensed electrician evaluate and correct the issue to ensure proper and safe wiring. Connecting a four-prong outlet with reversed hot wires can be a safety hazard and needs to be addressed by a professional.
Bring power into the light switch box 12/2 or 14/2 wire depending on the existing wire. Make sure you use the exactly same size wire that is used on that circuit. If you do not know look at the breaker in the main panel that controls power to that circuit. 20 amp will be 12/2 wire and 15 amp will be 14/2 wire. Now run another wire from the switch box out to the outlet. Inside the switch box, strip both white wires back 3/4" and connect them together under a wire nut and push this back into the box. Connect the 2 ground wires together and then connect that to the ground screw on the switch. You now have 2 black wires left. Connect them to the 2 screws on the light switch. Does not matter which black wire you connect to which screw. At the outlet connect the ground wire to the green ground screw, black wire to copper screw, and white wire to silver screw. That outlet will now be controlled by the light switch.
The fan is probably a 115 VAC single phase fan and the outlet is probably a 230 VAC "two phase" outlet. The fan would then have the following wires: hot (black), neutral (white), and ground (green). The outlet would then have the following wires: hot #1 (black), hot #2 (red), neutral (white), and ground (green). Pick either of the two hot wires on the outlet and connect the hot wire of the fan to that (ignore the other hot wire on the outlet) and connect the neutral to neutral and ground to ground. If the wire colors are not as I described above you may have something else (e.g. 3-phase) and that would be wired differently, but those systems are usually used only in industrial settings not the home.
To change a 2 prong outlet to a 3 prong outlet in your home, you will need to replace the old outlet with a new one that includes a ground wire. This typically involves running a new wire from the outlet to the electrical panel to provide the necessary grounding. It is important to follow safety guidelines and consult a licensed electrician to ensure the job is done correctly and safely.