0
What else can I help you with?
When a circuit breaker trips in what position will you find the operating handle?
The operating handle will be found in mid throw. On smaller type electrical breakers there is a small trip indicator window and a red flag will be visible when the breaker has tripped. On larger physical size breakers you will definitely see that the handle is not in the off or on position. To reset any size breaker move the handle to the full off position. You might hear a click but you will definitely feel the internal mechanism re-latch to the off position. This has reset the breaker, move the handle to the on position and normal electrical power will have been restored. If you get an instantaneous trip after a reset do not try and reset the breaker again. Find the cause of the short circuit and get it repaired. Constant and repetitive resetting will destroy the breaker and increase the temperature of the short circuit. If the short circuit is in a highly combustive area this is not good. Find the problem and get it repaired.
Why is the power off on on breaker when it is not flipped off?
Turning the breaker on allows the power to flow through to the outlets, lights, and appliances on that circuit, so yes power goes to and through a turned on breaker. If the breaker is off, but the main power is on, power still get to the breaker, usually from the bus bar that runs down the middle of the back of the breaker box.
The electrical Breaker will not reset?
To reset a breaker move the handle completely to the off position. If it had tripped you will feel a little resistance as it goes to the off position. If this doesn't restore the power the breaker is either bad and in need of replacement, or there is a persistent fault in the circuit causing the breaker to immediately re-trip. Breakers are safety devices.
Should a circuit breaker get hot on very hot days?
If a breaker isn't tripping, yet still feels quite warm, you probably are close to having too many appliances on its circuit. Breakers trip because of overloads (too many appliances), or shorts ( bare wires touching each other). These situations are quite dangerous and need to be corrected. If you can't find the problem, contact an electrician right away, and keep the circuit off.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
Is it normal for an electrical outlet to feel hot to the touch?
No, it is not normal for an electrical outlet to feel hot to the touch. This could indicate an issue with the wiring or the outlet itself, and it should be checked by a qualified electrician to prevent potential hazards like electrical fires.
What is the problem if the breaker isn't tripped and there is no power to my switch in computer room switch in foyer switch for outside porch and alarm panel is dead?
The most likely problem is that the breaker has tripped. On some breakers there is a indication window that shows a red flag if the breaker needs resetting. On other breakers there is no indication but a slight misalignment of the breaker handle as compared to the other ones. On the distribution panel find the breaker number of the circuit that is off from the panel index. Push the breaker handle to the furthest off position that you can. As the handle is moved to the off position you will feel a bit of resistance. Push past it as that is the breaker resetting. Return the breaker to the on position to see if the circuit has re-energized. The only other reason is that a wire has become disconnected in the circuit. If you have been doing any electrical work on the circuit start looking in that area. To troubleshoot these types of problems it will require the use of a volt meter to check to see if the circuit is "hot" from the breaker out. Then it is just a matter of finding where the voltage stops and locate the problem.
How do you identify the breaker for a currently dead circuit?
If the breaker is a Sq "D" there will be a red flag in the clear window on the face of the breaker. For all breakers including Sq "D", when in the trip fault position the handle will be between the full on and full off position. To reset the breaker move the handle over to the full off position. You should feel and hear a click. This is the breaker being reset. Then move the breaker handle over to the full on position. If the breaker trips instantaneously when moved to the on position do not reset it. Time to do some trouble shooting. Find out what is on that circuit and if any devices are plugged into it. Remove any plugged in devices from the circuit and try to reset again. If it still trips, leave the circuit off, it is time to call in an electrician. Wires that are short circuiting in the wall or in receptacle boxes can become dangerous very quickly if left energized.
Why is my cut hot to the touch?
A cut may feel hot to the touch due to inflammation, which is the body's natural response to injury. Inflammation increases blood flow to the area, causing it to feel warm. This is a normal part of the healing process.
What does it mean if you feel normal but people keep telling you that you're burning up all over and when you touch your own skin you can feel that it is almost too hot to touch?
You are either running a fever or having an adverse (allergic) reaction to something.
If i touch the surface of the brain how does it feel?
touch the surface of the brain how does it feel
What is the definition of touch?
The definition for touch is feel.
You feel something in the back of your vagina almost like a ball but when you touch it it doesn't have feeling I don't think it's normal and I don't know how long you have had it what is it?
Go to the doctor for an exam. He/she will tell you if this is normal.
