answersLogoWhite

0

The inner diameter of a shop vac hose is typically around 1-1/4 inches, while the outer diameter is usually around 1-1/2 inches.

User Avatar

AnswerBot

4mo ago

What else can I help you with?

Related Questions

How can one accurately measure a shop vac hose?

To accurately measure a shop vac hose, use a measuring tape or ruler to measure the diameter of the hose. Measure from one outer edge of the hose to the opposite outer edge. This measurement will give you the accurate size of the shop vac hose.


What is the shop vac hose size for this particular model?

The shop vac hose size for this model is 1.25 inches in diameter.


How can I accurately measure the size of a shop vac hose?

To accurately measure the size of a shop vac hose, use a measuring tape or ruler to determine the diameter of the hose. Measure across the opening of the hose to find the diameter in inches or millimeters. This measurement will help you identify the correct size for replacement or accessories.


What is the shop vac hose diameter for optimal performance and compatibility with various attachments?

The optimal shop vac hose diameter for performance and compatibility with various attachments is typically 1-1/4 inches to 2-1/2 inches.


What should an inner and outer tie rod replacement for a 2001 Lincoln Continental cost?

each shop that can do that kind of work will charge different prices, check around for the best deal.


Where do you get a hose on clubpenguin?

to get a hose you have to be a member and wait for the hose to pop up in the gift shop cataloge Stepheny1(thats my username to clubpenguin)


Where can you buy snake board wheels?

It depends on the model. Older models have bearings of an outer diameter bigger than regular skateboard wheels, and the axle is larger than the inner diameter of standard bearings. Newer models may have switched to a standard bearing. Skateboard shops sometimes have the proper sizes for older models, but roller skate wheels are closer. However the bearings do not fit standard wheels for skateboards or roller skates. If you have a good shop they can arrange to have the wheels ground out to accommodate the larger bearing, or you can have the axle machined to a smaller diameter and switch to standard bearings.


Can you demonstrate how to suck up water with a shop vac?

To suck up water with a shop vac, first make sure the vacuum is set to wet mode. Attach the appropriate hose or attachment for liquids. Place the hose into the water you want to remove and turn on the shop vac. Move the hose around to suck up all the water. Empty the shop vac when finished.


How do you change the bearings on a speed skate wheel?

You remove the wheel from axle then remove any clip holding the bearing and pop the entire bearing ( outer and inner race) out of the wheel. Take this bearing to a skate or bike shop to get an exact duplicate, or even to an industrial bearing shop to get abetter one.


What happens in Liposuction?

They stick a hose in your but and hook it up to a shop vac


What is the best shop vac to use with a table saw?

The best shop vac to use with a table saw is one that has strong suction power and a large capacity to effectively collect sawdust and debris. Look for a shop vac with a HEPA filter to trap fine particles and prevent them from circulating in the air. Additionally, consider a shop vac with a hose diameter that fits the dust port on your table saw for efficient dust collection.


Were can you find 1 inch intake hose for a aquarium filter?

in a hardware shop.

Trending Questions
Is there a way to detect and repair an expansion tank leak in a heating system? What information can be found in the equipment grounding conductor table? What are some stylish ways to incorporate hanging lights in a living room? How many 12/2 wires can fit in a 1/2 conduit? How can I repair a chain link fence? What are the best practices for installing a foundation protection board to safeguard a building's base from moisture and other potential damage? What are the benefits of using foil faced rigid insulation in a construction project? What are the different options available for toilet trim and how can I choose the best one for my bathroom? What is the purpose of an overflow drain stopper in a bathtub? How can the feather board be effectively utilized in woodworking projects? How can I properly protect my furniture with plastic wrap during a move or storage to prevent damage? How can I effectively use a steamer to remove wallpaper? What are the benefits of installing a cement board floor in a home renovation project? What are the best practices for installing Romex in conduit to ensure safety and compliance with electrical codes? What size and type of screws are needed to install a ceiling fan? Why won't my garage door open and what could be causing this issue? What is the code for the interrogation aq worlds? Is bored an emotion? What are some stylish and practical ways to incorporate a bath towel bar into a small bathroom space? How do you use a self-centering dowel jig effectively for woodworking projects?