0
What else can I help you with?
What type of wire gauge is used for a 30amp circuit?
10 gauge
How many conductors in 220v 30amp circuit using?
A 220V 30A circuit typically requires three conductors: two hot wires and one ground wire. An additional neutral wire may be needed depending on the specific electrical configuration or equipment being used.
What is the maximum amperage capacity of a 30amp breaker and how is it determined for electrical circuits?
The maximum amperage capacity of a 30-amp breaker is 30 amps. This capacity is determined based on the rating of the breaker, which is designed to trip and disconnect the circuit if the current exceeds 30 amps, protecting the electrical system from overloading.
Car Tail lights keep blowing its 30amp fuses?
you have a short somewhere on that circuit. you need to find it and repair it.
Why do you use a 30amp breaker on a ring circuit and a 20 amp on a radial circuit?
Answer for UK, Europe and countries running a 50 Hz supply service.A ring circuit has two routes to each outlet, a radial has only one.
Do I need a GFCI circuit breaker for a 220V 30amp Table saw?
Yes, it is advisable to use a GFCI (Ground Fault Circuit Interrupter) circuit breaker for a 220V 30-amp table saw, especially if it will be used in a garage or outdoor environment where moisture is present. GFCI breakers help protect against electrical shock by shutting off the circuit when a ground fault is detected. Check local electrical codes, as they may require GFCI protection for certain tools and equipment. Always prioritize safety when working with powerful machinery.
What size wire should be used for a clothes dryer on a 30AMP circuit?
In Europe we would like to see that on 6mm square conductors
Would it be a problem to make a twist lock extension cord and hook it to a 30amp twist lock plug on a dedicated circuit for a tanning bed?
Get naked and all will be well
Can a 240v 50amp circuit be changed to a 120v 30amp circuit?
Answer for USA, Canada and countries running a 60 Hertz supply service.Yes, a 240v 50amp circuit can be changed to a 120v 30amp circuit. The wire for the 50 amp circuit should be a #6. This is more than ample for a 30 amp circuit. Remove the two pole 60 amp breaker and replace it with a single pole 30 and a single pole 15 amp breaker. One of the two #6 wires will be terminated on the neutral bus (if there is a white use it) and the other #6 will be terminated on the new 30 amp breaker. This will give you the required 120 volt 30 amp circuit. The new 15 amp breaker that was installed just to fill the hole from the two pole 60 amp breaker will give you a spare 15 amp circuit. I have no idea what you are trying to do, but there is no way you can change 220v 50 amp to 120v 30 amp. You can take 220 volt input in the top of your circuit breaker box. Then half of one side will be 120v and half of the other side will be 120v. You can install a 30 amp fuse. You should hire an electrician.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energizedIF YOU ARE NOT REALLY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
Is there a starter fuse on a 2002 883 harley Davidson hugger?
No... it has a 30Amp circuit breaker located in the fuse box. It is an automatic reset type 'breaker that will reset to closed once it cools down.
Can you use an existing 30amp circuit for my new cook top which calls for 208v240v?
It depends on the voltage of the 30-amp circuit, which has to be 208 or 240 v, and it also depends on how much current the cook top takes, which must be less than 30 amps. If those two conditions are met you can use the existing circuit.
Where is the 30amp blower circuit breaker located 1999 ford escort?
It is located above the fuse panel inside the left kick panel, just left of the hood release. You need little hands to get to it.
