answersLogoWhite

0

The recommended type and size of cable for a 240-volt, 30-amp circuit is a 2 2 2 4 SER cable.

User Avatar

AnswerBot

4mo ago

What else can I help you with?

Related Questions

What is the recommended cable size for a 100 amp electrical circuit?

The recommended cable size for a 100 amp electrical circuit is typically 3 AWG copper or 1/0 AWG aluminum.


Have 240v 30amp breaker need to connect a 240volt 40 amp cooktop can you do this I have a 103 600volt wire the cooktop power supply requires 240volt 4 wire 60 hz?

Yes you can. As long as you don't use 40 amps. The 30 amp breaker may kick off if you use all things at once. So you are well protected but not up to code. The 4th wire required for the new stove is probably a ground fault wire. So run a new cable or cook slower.


What is a bad ground cable?

In an electrical circuit, you'll have a charged circuit (the positive), and a ground circuit... a bad ground cable is a cable which is somehow not effectively completing the ground.. could be poor conductive material, a break or fray in the cable, an improper grounding point..


What is the purpose of the black cable in this electrical circuit?

The purpose of the black cable in this electrical circuit is to carry the electric current from the power source to the connected devices or components in the circuit.


What are 3 type of electrical circuit?

Lighting CircuitsRadial CircuitsRing circuitsRing CircuitsA ring circuit can serve an area up to 110 square metres (120 square yards), 2.5mm2 cable is used to wire the circuit and the circuit has a 30amp fuse or 32amp MCB on the consumer unit. It is usual for a house to have one ring circuit upstairs and one ring circuit downstairs.Ring circuits can have extra sockets added to them by adding a 'spur' onto a ring circuit. A spur is a branch off the ring circuit, usually from an existing circuit, although a junction box could also be used. Theoretically as many spurs as sockets could be added, but the maximum load of the circuit (30/32amp) still exists).Radial CircuitsRadial circuits can therefore only serve a smaller area. Using 2.5mm2 cable combined with a 20amp fuse/MCB an area of 20 square metres (24 square yards) is permissible. For 4mm2 cable combined with a 32amp MCB or a 30amp cartridge fuse (a re-wirable fuse is not allowed) an area of 50 square metres (60 square yards) is permissible.In a similar way to ring circuits spurs can be added at points along the radial circuit if required. High powered appliances (cookers / showers) must have their own radial circuit.Lighting CircuitsLighting circuits are basically radial circuits. There are two distinct types of lighting, circuit the loop-in circuit and the older junction box circuit. Most houses combine aspects of both types of circuits. The loop-in circuit has a cable, running from light to light terminating at the last light as in the conventional radial circuits and then single cable run from the lights to the light switches.The other type of lighting circuit has a junction box for each light. The cable runs from the consumer unit to the first junction box and then onto the next terminating at the last junction box. Then another cable is run from each junction box to its light and another wire from the junction box to that light switch. The cable used for a lighting circuit is 1mm2 or 1.5mm2 for long runs.Another AnswerI think that this question is referring to more fundamental circuits than those described above. There are fourcategories of circuit: series circuits, parallel circuits, a combination of the two (series-parallel circuits), and complex circuits. Complex circuits describe circuits which don't fall into the first three categories.


What is the recommended burial depth for UF cable?

The recommended burial depth for UF cable is typically 24 inches underground.


What type of wiring should be used with a 20 amp circuit, specifically considering the keyword "Romex"?

For a 20 amp circuit, it is recommended to use 12-gauge Romex wiring. Romex is a brand of non-metallic sheathed cable commonly used for residential electrical wiring.


Which of the UTP cable categories is recommended as 100Base T media?

Which of the UTP cable categories is recommended as 100Base T media? CAT2,CAT3,CAT4,CAT5


What is the recommended cable size for a 200 amp service entrance cable?

The recommended cable size for a 200 amp service entrance is typically 2/0 AWG copper or 4/0 AWG aluminum.


How long is the main ring?

If you are talking about an electrical ring main it can be as long as you want it as long as it returns back to the circuit breaker with the other end of the cable, which if you didn't return the 2nd end of the cable to the circuit breaker you would have a radial circuit.


What is a characteristic on plenum rated cable?

Recommended for HVAC


What is the recommended cable length from the modem to the router or access point for wireless Internet connection?

what is submarine cable