answersLogoWhite

0

The standard hose fitting size for this application is 3/4 inch.

User Avatar

AnswerBot

4mo ago

What else can I help you with?

Related Questions

What is the standard garden hose size fitting for most outdoor faucets?

The standard garden hose size fitting for most outdoor faucets is 3/4 inch.


What is difference between tube connector and tube adapter fitting?

A tube connector is the standard fitting that goes on a tube or hose. A tube adapter fits to a tube or hose and enables it to connect to a fitting of a different size to its standard.


Are UK and US garden hose fittings the same standard size?

No, it appears that the UK and US garden hose fittings are not the same standard size. Apparently, the US standard fitting is a little bit bigger than the UK version.


What is a hose nipple?

A hose nipple is a push-on fitting that allows you to connect the hose to a threaded fitting. See related link below for a picture of a hose nipple.


Which is the high pressure hose for power steering for a 92 Chevy ck1500?

Normally a High Pressure hose will have bigger hydraulic fitting than the low pressure or "return". In fact if the low pressure hose has been serviced sometime it will just have a standard hose clamp on it.


What is ms fitting?

A flare less fitting used to connect tubing or hose.


How do you replace heater hose bypass fitting?

Replacing the heater hose bypass fitting will depend on how the fitting was installed. It could be screwed or bolted in. Try searching for your specific vehicle for a detailed description of the install.


What are hydraulic hose pipe fitting manufacturing suppliers in India?

polyhose is the best hydraulic hose pipe fitting manufacturing suppliers in india.Polyhose is the largest hose manufacturer of industrial & hydraulic hose pipes in India, United States, UK & Germany. PTFE tubing and hose manufacturer.


Where should the male fitting of a fire hose be located when it is rolled up for storage?

The male fitting of a fire hose, when rolled, should be on the inside (in the center) of the rolled hose.Also, varying by the station or district protocols, if the female fitting is on the inside, it means that the hose is out of service or damaged.


How can one accurately measure a hose for proper sizing and fitting?

To accurately measure a hose for proper sizing and fitting, use a tape measure to determine the hose's inner diameter and length. Ensure the measurements match the specifications of the fitting or equipment it will be connected to. Additionally, consider the material and pressure rating of the hose to ensure it is suitable for the intended use.


Where is the thermostat on a 1999 Chrysler cirrus?

4 cylinder : under upper radiator hose fitting on engine.6 cylinder : under the housing that lower hose hooks to.4 cylinder : under upper radiator hose fitting on engine.6 cylinder : under the housing that lower hose hooks to.


Will a broken chemical hose fitting cause your pressure washer to blow out water from fitting?

Yes, it very likely will.

Trending Questions
What are some creative ways to utilize the bathtub ledge for storage or decor in a small bathroom? What are the benefits of a foldable wooden table for small living spaces? How can I prevent water from accumulating in the dryer drum? How do I properly operate the shower on-off valve to control the water flow in my bathroom? How important is sanding in between coats of polyurethane for achieving a smooth and professional finish? What are the best tips for using a planting auger for drill effectively in gardening and landscaping projects? What are the best features to consider when choosing an outdoor wall mount light for your home? How can I enhance the appearance and functionality of my home by investing in attic finishing? What is the recommended length and type of electric stove cord to use for safe and efficient operation? What is the purpose of the freezer defrost cycle and how does it help maintain the efficiency of the appliance? How important is it to use a wood conditioner pre-stain before applying stain to ensure a smooth and even finish on your project? How long should you wait for grout to dry before showering? What information should be included on an electrical box label? What are the key components required to build a functional doorbell circuit? What is considered a safe radon level in a home and how can it be ensured? What are the benefits of using tung oil flooring in a home renovation project? How can I effectively remove haze from tile surfaces? What are the common causes of wall cracks and how can they be effectively repaired? Why isn't the toilet flushing properly? How can I properly install shelving cleats to maximize storage space in my home?