0
What else can I help you with?
What is the recommended bolt size for a TV wall mount installation?
The recommended bolt size for a TV wall mount installation is typically M8 or 5/16 inch in diameter.
How can I secure my French doors using a cremone bolt?
To secure your French doors using a cremone bolt, you can install the bolt on the inactive door leaf. This will allow you to secure both doors by turning the bolt handle to engage the locking mechanism. Make sure to follow the manufacturer's instructions for proper installation and operation.
What is the recommended installation method for a 1/4 hanger bolt in a wooden structure?
The recommended installation method for a 1/4 hanger bolt in a wooden structure is to pre-drill a hole slightly smaller than the bolt diameter, then screw the hanger bolt into the hole using a wrench or socket tool. This will ensure a secure and stable connection.
How can I install a molly bolt properly?
To install a molly bolt properly, first drill a hole in the wall, insert the molly bolt into the hole, and tighten it with a screwdriver until it is secure. Make sure the molly bolt is flush with the wall surface for proper installation.
How do you change a motor mount in a 1989 Plymouth voyager se v6 3.0L?
Well. if its your front mount, then you jack up the engine, your mount is located at the very front, at the bottom, then you remove the single bolt that goes through the mount, remove the mount, and installation is the reverse of removal.
How do you properly perform toggle bolt installation for securing heavy objects to drywall?
To properly perform toggle bolt installation for securing heavy objects to drywall, first drill a hole in the drywall, insert the toggle bolt through the hole, and tighten it until secure. Then, attach the object to the bolt using a screw or hook. Make sure the toggle bolt is the appropriate size and weight capacity for the object being secured.
How do to remove a stripped motor mount bolt on a SSEI Bonneville?
Well your gonna have to have a new mount bolt. Drill it out so that the drill bit is the same size as the hole the bolt goes into. Snap the head off when you drill past thehead. The bolt should hand screw out. If not use vicegrips. Then put the new one in the same place. Should replace the mount aswell.
What size bolt should I use for a TV mount?
When choosing a bolt for a TV mount, look for one that is the same size as the mounting holes on the back of your TV. Typically, a 6mm or 8mm bolt is commonly used for most TV mounts. Be sure to check the specifications of your specific TV mount to ensure you are using the correct size bolt.
What type of fastener is commonly used to secure a nut to a bolt?
The type of fastener commonly used to secure a nut to a bolt is a washer.
How do you replace the alternator on a 1987 Honda Civic DX?
Disconnect the negative battery cable. Remove the air cleaner assembly if necessary. Disconnect the electrical connectors from the alternator. Loosen the alternator adjusting bolt or nut and through-bolt and remove the alternator belt. Remove the alternator adjusting bolt or nut and through-bolt and remove the alternator. If necessary, remove the mount bracket bolts and the upper and lower mount brackets. Installation is the reverse of the removal procedure: put the alternator in place and re-bolt mount bracket (if removed). Engage the electrical connectors and install the air cleaner assembly (if removed).
How do you remove a 89 caprice oil pan?
remove the bolt in the motor mount. and remove the bolt to the trans mount. then lift the engine with a engine lift, hoist point should be around the intake man near the ac compressor you should be able to get it from there or you might need to loosen both motor mounts
How do you replace the alternator on a 1990 Chevy Celebrity V6 automatic?
I have a 1989 celebrity and it was quiet easy to change the alternator, done it a dozen times. There should be 1 main bolt in the back on the bottom of the alternator,(side toward cab). This bolt goes all the way through the mount. Then on the front side there should be a bolt that screws into a mount. Disconnet the main battery cable and unplug the wires on the bottom and there it should be loose.
